16. Locate the Tray (35) on the Lat Tower (4) (see the | 16 |
|
|
| 86 |
|
|
inset drawing). Remove the two preassembled |
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
| Edges |
| ||
5/16” x 3/4” Button Head Screws (86) and the |
|
|
|
|
| ||
|
|
|
|
| up |
| |
Cover Plate (72) from the Tray. |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
Set the Resistance Bars into the Tray (35) in the |
|
|
|
| 72 |
|
|
|
|
|
|
|
|
| |
following order: the |
|
|
|
|
|
| 96 |
Resistance Bar (67), the |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
Resistance Bar (36), an |
| Rings on |
|
|
|
|
|
(95), the |
| this side |
|
|
|
| 44 |
|
|
|
|
|
| ||
Resistance Bar (96). Make sure the indicated |
| 4 |
|
|
|
| 95 |
rings are on the side shown and the arrows |
|
| 35 |
|
|
| 95 |
point toward the Tray. |
|
|
|
|
|
| 36 |
|
| 35 |
|
|
| 67 | |
Reattach the Cover Plate (72), with the edges up, |
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
to the Tray (35) with two 5/16” x 3/4” Button Head | 17 |
|
|
|
|
|
|
Screws (86). |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
17. Locate the Long Cable (80). Insert one end of |
|
|
|
|
| 80 | 71 |
the Cable through the welded tube on the indicat- |
|
|
|
|
|
| |
|
|
|
|
| 11 |
| |
ed end of the Cross Tube (11) and then through a |
|
|
|
|
| 24 | |
|
|
|
|
|
| ||
Swivel Arm (22). If necessary, use the tip of a |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
screwdriver to pull the end of the Cable out of the |
|
|
|
|
|
| 22 |
Swivel Arm. Be sure the Cable is on the indicat- |
|
|
|
| 28 |
| |
|
|
|
|
|
| ||
ed side of the welded rod in the Swivel Arm. |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Rod |
Insert the Swivel Arm (22) into the welded tube |
|
|
|
|
|
| 103 |
on the Cross Tube (11). Secure the Swivel Arm |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
with a #8 x 3/8” Screw (24). |
|
|
|
|
|
|
|
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
|
|
|
|
(28). Attach the Pulley inside of the Swivel Arm | 18 |
|
|
|
|
|
|
(22) with a 3/8” x 1 1/2” Button Head Bolt (71) |
|
|
| Flat |
|
| |
|
|
|
|
|
| ||
and a 3/8” Nylon Jamnut (103). |
|
|
|
| Edge | 29 | 76 |
|
|
|
|
|
| ||
18. Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
|
|
|
|
(28). Attach the Pulley and a Pulley Guard (29) to |
|
| 73 |
|
|
| 80 |
the indicated 3/8” x 5 1/2” Carriage Bolt (73) with |
|
|
|
|
| 28 | |
a 3/8” Nylon Locknut (76). Be sure the flat edge |
|
|
|
|
|
| |
of the Pulley Guard is on the side shown. |
|
|
|
|
|
|
|
19. Attach a Pulley Housing (94) to the indicated “U”- | 19 |
|
|
|
|
|
|
channel on the |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
(44) with a 3/8” x 4” Bolt (66) and a 3/8” Nylon |
|
|
|
|
|
|
|
Locknut (76). |
|
|
|
|
|
|
|
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
| 44 |
|
|
|
(28). Attach the Pulley inside of the Pulley |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
Housing (94) with a 3/8” x 1 1/2” Button Head |
|
| 76 |
|
| ||
Bolt (71) and a 3/8” Nylon Jamnut (103). |
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
| 71 |
|
| 103 |
|
|
|
|
| 94 |
| ||
|
|
|
|
|
| ||
|
|
| 28 |
|
|
|
|
|
|
|
| 80 | 66 |
| |
|
|
|
|
|
|
| |
| 10 |
|
|
|
|
|
|
