24. Slide an end of the Long Cable (80) through the | 24 |
|
|
|
|
Pulley Arm (22). Wrap the Cable around a 90mm |
|
|
|
| |
|
|
|
|
| |
Pulley (28). Attach the Pulley to the Pulley Arm |
|
|
|
|
|
with an M10 x 40mm Bolt (71) and an M10 Nylon |
|
|
| 71 |
|
Locknut (76). |
|
|
|
|
|
|
|
|
|
| 80 |
|
|
|
| 76 | 28 |
|
|
|
|
| |
25. Locate the Bench Cable (32). It has three ends, | 25 |
|
|
|
|
two that are the same length and a third that is |
|
|
|
| |
|
|
|
|
| |
longer. |
|
|
|
|
|
Route the long end of the Bench Cable (32) |
|
|
|
|
|
through the hole in the Front Leg (6), and attach it |
|
|
|
|
|
inside the hole in the Leg Lever (7) with an M10 x |
|
|
|
| 63 |
60mm Bolt (63), two M10 Washers (75), and an |
|
|
|
|
|
M10 Nylon Locknut (76). |
|
| 32 | 6 | 75 |
|
|
| |||
|
|
| 76 | 7 | |
|
|
|
| ||
|
|
|
| 75 |
|
26. Attach a 90mm Pulley (28) inside the hole in the | 26 |
|
|
|
|
Front Leg (6) with an M10 x 66 mm Bolt (79), two |
|
|
|
| |
|
|
|
|
| |
12.5mm Spacers (52), two M10 Washers (75), |
|
|
|
|
|
and an M10 Nylon Locknut (76). Be sure the |
|
|
|
|
|
Pulley is over the Bench Cable (32). |
|
|
| 5 |
|
|
|
|
|
| |
Slide the two free ends of the Bench Cable (32) |
|
|
|
| 75 |
onto the eyebolt welded to the bottom of the |
|
|
|
| |
|
|
|
|
| |
Bench Frame (5). |
| 32 |
|
| 79 |
| Eyebolt | 28 |
| 52 | |
|
|
| 75 |
|
|
|
|
| 76 | 52 |
|
|
|
|
|
| |
27. Locate the two Short Cables (33). Wrap a Short | 27 |
|
|
|
|
Cable around a 90mm Pulley (28). Attach the |
|
|
|
| |
|
|
|
|
| |
Pulley to a Pulley Housing (21) with an M10 x |
|
|
| 21 |
|
40mm Bolt (71) and an M10 Nylon Locknut (76). |
|
|
|
| |
|
| 76 |
| 71 |
|
Repeat this step with the other Short Cable |
|
|
|
| |
(33). |
|
|
|
|
|
|
|
| 28 | 33 |
|
|
|
|
|
| |
| 12 |
|
|
|
|
