16.Press a 1 1/2” x 2” Inner Cap (21) into the Right Butterfly Arm (26). Wet the lower end of the Arm with soapy water. Slide a Long Pad (54) onto the Arm.
Attach a Press Handle (27) to the Right Butterfly Arm (26) with two 5/16” x 3/4” Button Head Screws
(51)and two Nut Clips (108). Slide the Long Pad
(54)down so that the bottom is flush with the lower end of the Arm. Press a 1” Round Inner Cap (29) into the Press Handle. Wet the Press Handle with soapy water. Slide a Long Handgrip (28) onto the Press Handle.
Lubricate a 3/8” x 2” Bolt (100) with grease. Attach a Pivot Bracket (70) to the Right Butterfly Arm (26) with the Bolt and a 3/8” Nylon Jamnut (113). Do not overtighten the Nylon Jamnut; the Pivot Bracket must be able to pivot easily. Repeat this step with the Left Butterfly Arm (25).
17.Lubricate a 3/8” x 3” Button Head Bolt (104) and both sides of two Plastic Washers (56) with grease. Attach the Right Butterfly Arm (26) to the Butterfly Frame (47) with the Bolt, the two Plastic Washers, two Butterfly Caps (57), two 3/8” Washers (91), and a 3/8” Nylon Jamnut (113) as shown. Make sure that the recessed sides of the Plastic Washers are fitted over the welded bushing in the Butterfly Arm. Do not overtighten the Nylon Jamnut; the Butterfly Arm must be able to pivot easily.
Repeat this step with the Left Butterfly Arm (25).
16 |
| Lubricate |
| |
|
|
| ||
|
| 26 |
| 100 |
|
|
| 70 | |
|
|
|
| |
|
|
|
| 113 |
| 51 |
| 21 |
|
|
|
|
| |
54 |
|
|
| 25 |
108 |
| 28 |
|
|
|
|
|
| |
|
| 29 |
|
|
|
| 27 |
|
|
17 |
| 104 |
| |
|
|
| ||
| 26 | 56 | 91 |
|
|
|
| ||
|
|
| 57 | 47 |
|
|
|
| |
|
| 57 |
|
|
|
| 91 |
| 25 |
|
| 113 |
| |
18.
CABLE ASSEMBLY
IMPORTANT: Refer to the Cable Identification Chart on page 26 for help identifying the cables. Do not overtighten the bolts and nuts attaching the pulleys. The pulleys must be able to turn freely.
18 |
|
|
|
| |
|
|
|
|
| |
|
|
|
| ||
78 |
|
| |||
74 | |||||
|
|
|
| ||
Locate and open the parts bags labeled “CABLE ASSEMBLY” and “PULLEYS.”
Lubricate the 3/8” x 7” Bolt (30) with grease. Attach the Swivel Cage (76) to the Swivel Carriage (46) with the Bolt and a 3/8” Nylon Locknut (87).
Locate the Swivel High Cable (74), which is
126 1/2” long and has a ball on one end and a threaded bolt on the other end. Wrap the Cable around a 3 1/2” Pulley (78). Attach two Pulleys to the Swivel Cage (76) with two 3/8” x 1 3/4” Bolts (93) and two 3/8” Nylon Locknuts (87).
11
30 |
87 |
78 |
93 |
76 |
46 |
87 |
