![](/images/new-backgrounds/1302961/30296119x1.webp)
15. Slide the Leg Developer (19) into the Bench Rail | 15 |
|
|
|
(5). Align the hole in the Leg Developer with a |
|
|
| |
|
|
|
| |
hole in the Front Leg (6). Tighten the Bench Knob |
|
|
|
|
(42) into the hole in the Leg Developer. | 7 |
|
|
|
|
|
|
| |
Connect the eyebolt on the Leg Lever Cable (32) |
| 19 |
|
|
|
|
|
| |
to the indicated side of the Leg Lever (7) with an |
|
|
|
|
M8 Nylon Locknut (65). | 65 |
|
|
|
| Eyebolt |
|
|
|
| 5 |
|
|
|
| 32 | 42 |
|
|
| 6 |
|
| |
|
|
|
| |
16. Locate the Long Cable (80). Insert one end of | 16 |
|
|
|
the Cable through the welded tube on the indicat- |
|
|
| |
|
|
|
| |
ed end of the Cross Tube (11) and then through a |
|
| 80 |
|
Swivel Arm (22). If necessary, use the tip of a |
|
| 71 | |
screwdriver to pull the end of the Cable out of the |
|
| 107 | |
|
|
| ||
Swivel Arm. Make sure the Cable is on the indi- |
| 11 |
| |
cated side of the welded rod in the Swivel Arm. |
|
|
|
|
Insert the Swivel Arm (22) into the welded tube |
| 28 |
| 22 |
|
|
| ||
on the Cross Tube (11). Secure the Swivel Arm |
|
|
| |
|
|
|
| |
with an M4 x 5mm Screw (107). |
|
|
| Rod |
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
| 76 |
|
|
|
| |
(28). Attach the Pulley inside of the Swivel Arm |
|
|
|
|
(22) with an M10 x 42mm Button Head Bolt (71) |
|
|
|
|
and an M10 Nylon Locknut (76). |
|
|
|
|
17. Wrap the Long Cable (80) around a 90mm Pulley | 17 | Flat |
|
|
|
|
| ||
(28). Attach the Pulley and a Pulley Guard (29) to |
| Edge | 29 | 76 |
the indicated M10 x 140mm Carriage Bolt (73) |
|
| ||
|
|
|
| |
with an M10 Nylon Locknut (76). Make sure the |
|
|
|
|
flat edge of the Pulley Guard is on the side |
|
|
| 80 |
shown. | 73 |
|
| |
|
| 28 | ||
|
|
|
| |
18. Attach a Pulley Housing (94) to the indicated “U”- | 18 |
|
|
|
channel on the |
|
|
| |
|
|
|
| |
(44) with an M10 x 102mm Button Head Bolt (24), |
|
|
|
|
two Pivot Bushings (74), and an M10 Nylon |
|
|
|
|
Locknut (76). |
|
|
|
|
Wrap the Long Cable (80) around a 90mm Pulley | 44 |
|
|
|
76 |
|
|
| |
(28). Attach the Pulley inside of the Pulley |
|
|
| |
|
| |||
Housing (94) with an M10 x 42mm Button Head | 74 |
| ||
|
|
| ||
Bolt (71) and an M10 Nylon Locknut (76). |
| 76 |
| |
71 |
|
| ||
|
|
| ||
| 94 |
|
| |
|
|
|
| |
| 28 | 74 |
|
|
|
|
|
| |
| 80 | 24 |
|
|
|
|
|
| |
| 10 |
|
|
|