8. | Attach a Large Pulley (14) and the Pulley Plate | 8 |
|
|
|
| (68) to the Upright (2) with an M12 x 62mm |
|
|
| |
|
|
|
|
| |
| Button Bolt (81) and an M12 Nylon Locknut (13). |
|
| 68 |
|
| Do not tighten the Locknut yet. |
|
| 13 | |
|
|
|
| ||
|
|
|
| 14 |
|
|
| 81 |
| 2 |
|
|
|
|
|
| |
9. | Pull the Upper Cable (115), which is attached | 9 |
|
|
|
| inside of the Mech Frame (not shown), up |
|
|
| |
|
|
|
|
| |
| between the Upright (2) and the Pulley Plate (68). |
|
|
|
|
|
|
|
|
| 115 |
| Attach another Large Pulley (14) to the Upright (2) |
|
| 90 | 11 |
|
|
|
| ||
| and the Pulley Plate (68) with an M12 x 62mm |
|
|
| |
|
|
|
|
| |
| Button Bolt (81) and an M12 Nylon Locknut (13). |
|
| 13 |
|
| Make sure that the Upper Cable (115) is |
|
|
| |
| between the two Pulleys. |
|
| 68 | |
| Hold the 38mm Spacer (90) inside the loop of the | 81 |
| 2 | 14 |
|
|
|
| ||
| Upper Cable (115), and between the Upright (2) |
|
|
| |
|
|
|
|
| |
| and the Pulley Plate (68). Attach the Spacer with |
|
|
|
|
| an M10 x 58mm Button Screw (11). Make sure |
|
|
|
|
| the ends of the cable do not wrap around |
|
|
|
|
| each other below the Spacer and the Large |
|
|
|
|
| Pulleys (14) used in steps 8 and 9 (see the |
|
|
|
|
| CABLE DIAGRAM on page 18). |
|
|
|
|
| Tighten the M12 Nylon Locknuts (13) used in |
|
|
|
|
| steps 8 and 9. |
|
|
|
|
10. | Attach a Small Guide Spacer (18), a Large Guide | 10 |
|
|
|
| Spacer (17), and two Crossbar Guides (15) to the |
|
|
| |
|
|
|
|
| |
| Upright (2) with an M10 x 152mm Bolt (86). |
|
|
|
|
| Pull the Upper Cable (115) up between the |
| 17 |
|
|
| Crossbar Guides (15). Press the metal cover on | 18 |
|
| |
|
|
| 86 | ||
| the cable into the groove in the Crossbar Block |
|
| ||
|
|
|
|
| |
| (16). Attach a Small Guide Spacer (18), the |
| 15 |
|
|
| Crossbar Block, the two Crossbar Guides (15), an |
| Metal |
| |
|
|
| 54 | ||
| M10 Thick Washer (54), and the two Tethers (70) | 2 | 115 | Cover | |
| to the Upright (2) with another M10 x 152mm Bolt |
|
|
| |
|
|
|
|
| |
| (86). Do not tighten the Bolt yet. |
|
|
| 86 |
|
|
|
|
| 70 |
|
| 18 | 16 | Groove |
|
|
|
|
|
| |
9
