Burner Controls
Figure 1 1a. – Interrupted ignition,
Figure 1 1b. – Interrupted ignition,
L1
L2 SAFETY AND
OPERATING
LIMITS
IGNITER
MOTOR
OIL VALVE
60 | 70 |
| L1 |
|
50 | W |
|
| |
80 |
|
|
| |
50 | 80 |
| L2 | SAFETY AND |
| R |
|
| OPERATING |
60 | 70 |
|
| |
|
|
|
| LIMITS |
THERMOSTAT |
|
|
| |
|
|
|
| IGNITER |
| IGNITER |
|
|
|
| L2 (IGN) |
|
|
|
| MOTOR |
|
|
|
| L2 (MTR) |
|
| MOTOR |
| L1LIMIT | L1 - | LIMIT | |
|
| |||
| LIMIT | JUMPER |
| |
| L2 |
|
|
|
| VALVE | TR |
| OIL VALVE |
| L2 (VLV) | TW |
| |
|
|
| ||
60 | 70 |
|
50 | 80 |
|
| W |
|
| R |
|
50 | 80 |
|
60 | 70 |
|
THERMOSTAT |
| |
| IGNITER |
|
| L2 (IGN) |
|
| MOTOR |
|
| L2 (MTR) |
|
| L1 |
|
| LIMIT | |
| L2 | JUMPER |
| VALVE | TR |
| L2 (VLV) | TW |
CAD |
| |
CELL | LOCATED ON OPPOSITE |
|
CAD CELL | SIDE OF CONTROL | CAD CELL |
|
CAD | |
CELL | LOCATED ON OPPOSITE |
| SIDE OF CONTROL |
Reset Button Operation
Table 2 explains what action the control will take when the reset button is pressed for different lengths of time during the various burner operating states.
Table 2 - Reset Button Operation
If the burner is in the |
| Pushing the reset button will: |
| ||||
|
|
|
|
|
| ||
below state: | Button Click |
|
| Button Hold |
| Button Hold | |
|
| (press < 1 second) |
| (press > 1 second) |
| (press 15+ seconds) | |
Lockout |
| Reset from Soft Lockout |
| Reset from Restricted (Hard) | |||
|
| Lockout | |||||
|
|
|
|
|
|
| |
Go to Pump Prime (see |
| Disable the Burner: |
| Enables Pump Priming: | |||
Ignition, Ignition Carryover | “Priming the Pump” above) |
| Any time the burner is running, |
| After the reset button has been | ||
|
|
|
| press and hold the reset button |
| held for 15 seconds, the button | |
|
| Yellow light flashes to indicate |
|
| |||
Run (igniter is shut off) | cad cell resistance. See “Cad |
| to disable the burner. The |
| can then be clicked during the | ||
Cell Resistance Indicator” for |
| burner will remain off as long |
| next ignition sequence to enter | |||
|
| table of resistance values. |
| as the button is held. |
| Pump Prime mode. | |
No action |
|
|
|
|
| ||
Standby |
|
|
|
|
|
|
|
Pump Prime |
| No action |
| Exit Pump Prime mode and return to Standby | |||
Table 3 - Status Lights |
|
|
|
|
|
| |
|
|
|
|
|
| ||
Light Color |
| On Continuously |
|
| Flashing | ||
|
|
|
|
|
| ||
Red | Restricted (Hard) Lockout |
|
| Soft Lockout |
| ||
Green | Flame Sensed during normal operation (Could | Recycle |
| ||||
| be stray light during standby) |
|
|
|
|
| |
Yellow
Control is in Pump Prime mode or
Reset button currently held for 15+ seconds.
Cad Cell resistance. See “Cad Cell Resistance Indicator” on page 18 for a table of resistance values.
Page 16 | 6104BAFG6104BAFGR065 |
