12.Apply window gasket (G). Measure from right inside edge of window frame to left inside edge. Then cut the window gasket, with square ends, to fit. Raise window sash slightly and place gasket over the top mounting channel and top edge of filler boards. See Figure 14.

13.Make sure filler boards are as far forward (toward inside room) in window channels as possible.

14.Insert foam blocks (f-f). Measure the distance between the filler board and the back window channel edge. Cut foam blocks W (6 mm) wider than measurement. Insert foam blocks into window channels - behind filler boards. See Figure 15.

15.Fasten cabinet to window sill. Lower window sash firmly onto cabinet. Place a carpenter’s level inside the cabinet and make sure cabinet is level side-to-side. Then drill starter holes into the cabinet base and the window sill. Use round-head wood screws (I) to fasten cabinet to window sill. See Figure 16.

16.Make sure cabinet has proper outward slope. Place carpenter’s level in the right side of the cabinet. There should be a 34 bubble tilt (W [6 mm]) titt toward the outside. Repeat for left side of cabinet. See Figure 17.

17.Attach 2%’ (64 mm) seal strip (J) to inside of cabinet. Make sure the seal strip is flush with the front edge of the cabinet. This seal strip provides a seal between the air conditioner base and the cabinet.

16.Assemble the outside support. Attach the vertical supports (K) to the angle supports (L). Use the round-head bolts (M), flat washers (N), lock washers (0) and the nuts

(P)for attachments. Then attach these supports to the bottom of the cabinet, but DO NOT tighten the botts at this time.

Attach the wall rail (Cl) the bottom of the supports, and slide the support assembly toward the house until the wall rail presses firmly against the wall. See Figure 16.

Now tighten all bolts. Tighten angled support bolts last so wall rail fits tightly against the house.

NOTE: If your house is constructed of materials that could be damaged by the wall rail, fasten a board between the wall rail and the house.

12.Colocar la empaquetadura de la ventana (G). Medir desde el borde interior derecho del marco de la ventana al borde interior izquierdo. Luego cortar la empaquetadura

de la ventana con 10s extremes cuadrados para que calce. Levantar levemente la hoja de la ventana y colocar la empaquetadura sobre la canaleta de montaje superior y en las tablas de relleno del borde superior. Ver Flgura 14.

13.Asegurarse de que las tablas de relleno eot&r tan adelante (hacia adentro de la habitation) en las canaletas de la ventana corno sea poslble.

14.Inserter for bloques de espuma (H). Medir la distancia entre la tabla de relleno y el borde de la canaleta trasera de la ventana. Cortar bloques de espuma 6 mm (W) m&s anchos que la medida. lnsertar los bloques de espuma dentro de las canaletas de la ventana detras de las tablas de relleno. Ver Figura 15.

15.Instalar la caja meMica en la batiente ds la ventana. Bajar la hoja de la ventana firmemente hasta la caja metalica. Colocar un nivel de carpintero dentro de la caja met&a y asegurarse de que la caja esta nivelada de un lado al otro. Luego taladrar orificios guia en la base de la caja metalica y en la batiente de la ventana. Usar 10s tornillos de madera de cabeza redonda (I) para sujetar la caja metalica a la batiente de la ventana. Ver Figura 16.

16.Asegurese de que la caja metilica tenga una inclination hacia afuera decuada. Colocar el nivel de carpintero en el lado derecho de la caja met&a. Debe tener una inclinacidn hacia afuera de aproximadarnente media burbuja (6 mm [WJ). Repetir para el lado izquierdo de la caja metalica. Ver Figura 17.

17.lnstalar la clnta obturadora de 64 mm (2%‘) (J) en la parte interior de la caja mstilica. Asegurarse de que la cinta obturadora este al ras con el borde delantero de la caja rnetalica. Esta cinta obturadora se coloca entre la base del acondicionador de aire y la caja met&a.

16. Montaje del soporte exterior. Unir 10s soportes verticales

(K)a 10s soportes angulares (L). Usar 10s pemos de cabeza redonda (M), las arandelas planas (N), las arandelas de seguridad (0) y las tuercas (P) coma sujeciones. Luego instalar estos soportes en la pafte inferior de la caja metalica, pero NO apretar 10s pemos en este momento.

lnstalar el travesaiio de la pared (Q) en la parte inferior de 10s soportes y deslizar el conjunto del soporte contra la pared de la casa hasta que el travesaiio descanse firmemente contra la pared. Ver Figure 18.

Ahora apretar todos 10s pemos. Apretar al final 10s pernos del soporte angular para que el travesaiio de la pared ajuste firmemente contra la pared de la casa.

NOTA: Si su casa esta construida de materiales que pueden dafiarse al instalar el travesaiio de la pared, instalar una tabla entre el travesaho y la pared de la casa.

16

Page 17 Page 19
Page 18
Image 18
Whirlpool ACM184XA0 manual
Page 17 Page 19

ACM184XA0 specifications

The Whirlpool ACM184XA0 is a sophisticated kitchen appliance designed to enhance cooking efficiency and versatility. Built with modern technology and a sleek design, this appliance stands out for its innovative features.

At the core of the ACM184XA0 is a high-performance induction cooking system that offers rapid cooking times and precise temperature control. Induction cooking heats up cookware directly through electromagnetic energy, ensuring that heat is generated only when suitable cookware is placed on the surface. This significantly reduces cooking time, making it a perfect option for busy households.

One of the notable features of the Whirlpool ACM184XA0 is its intuitive touch control panel, which provides easy access to a range of cooking functions. Whether you're simmering sauces, frying, or boiling, the interface allows for quick adjustments to settings with a simple touch. The appliance also includes multiple cooking zones, each with varying power levels, accommodating pots and pans of different sizes.

Safety is a primary consideration in the design of the ACM184XA0. The appliance is equipped with features such as auto shut-off and pan detection, which ensures that the induction element is only activated when suitable cookware is present. This not only prevents accidents but also enhances energy efficiency, making the cooking process more environmentally friendly.

In addition to its performance features, the Whirlpool ACM184XA0 boasts a sleek, modern aesthetic that fits seamlessly into any kitchen décor. Its minimalist design, complemented by a smooth glass surface, is not only visually appealing but also simplifies cleaning.

This induction cooktop also incorporates an innovative heat control feature, allowing users to maintain a steady temperature, which is ideal for melting chocolate or preparing delicate sauces. Furthermore, the appliance's rapid heat-up function ensures that cooking is not only efficient but also enjoyable.

With its combination of advanced technology, user-friendly controls, and stylish design, the Whirlpool ACM184XA0 is ideal for both novice cooks and seasoned chefs. It embodies the perfect blend of functionality and aesthetics, making it a valuable addition to any modern kitchen. Whether you're whipping up a weekday dinner or hosting a weekend gathering, this induction cooktop is designed to meet all cooking needs with ease.
Top Page Image Contents