9.Attach cabinet to finish frame. Drill 4 holes on each side and 2 holes in the top of the cabinet into the finish frame. Use #lo x 1” (25 mm) wood screws to attach cabinet to the frame. See Figure 27.

IMPORTANT: Do not overtighten screws or the cabinet will distort and provide a poor air seal between the cabinet and the air conditioner.

10.Place the 2%’ (63.5 mm) seal strip (J) inside the cabinet. Make sure the seal is flush with the cabinet front edge. See Figure 28.

NOTE: This seal strip fits between the air conditioner base and the cabinet.

11.Insert drain cup (I). Place drain cup through hole in cabinet rail. See Figure 29.

12.Insert air conditioner Into cabinet.

13.Reattach ground wire with grounding screw. Put excess grounded wire between the coils and the cabinet.

Electrical Shock Hazard

Air conditioner ground wire must be attached to the cabinet.

Failure to do so could resuft in electrical shock.

14.Attach the front panel. Remove the 2 front panel screws from unit base. Replace front panel by pushing it straight on and then lowering it slightly to lock it in place. Attach bottom front of panel by reinserting the 2 front panel screws. See Figure 30.

15.Caulk all outside wall openings around the installa- tion and cabinet.

16.Install decorative molding. If desired, install molding around room side of cabinet.

9.Colocar la caja metllica en el rnarco de acabado. Taladrar 4 agujeros a cada lado y 2 a trav& de la pane superior de la caja metalica hacia el marco. Usar 10s tornillos de madera #10 x 25 mm (1”) para sujetar la caja metalica al marco. Ver Figura 27.

IMPORTANTE: No apretar demasiado 10s tomillos pues la caja metalica se deformare y no obturara bien el aire entre la caja met&a y el acondicionador de aire.

10.Colocar la cinta obturadora de 83,5 mm (2.5’) (J) dentro de la caja metilica Asegurarse de que la cinta obturadora este al ras con el borde delantero de la caja met&a. Ver Figure 28.

NOTA: Esta cinta obturadora calza entre la base del acondicionador de aire y la caja met&a.

11.Insertar la taza de drenaje (T). Colocar la taza de drenaje a traves del agujero en el travesafio de la caja. Ver Figura 29.

12.lnsertar el acondicionador de aire en la caja metalica.

13.Vofver a instalar el alambre de puesta tlerra en el tornillo de puesta tierra. Colocar el exceso del alambre de puesta a tierra entre 10s serpentines y la caja metalica.

Riesgo de Choque EMctrko

El alambre de puesta a tierra del acondiiionador de aire debe ser conectado a la caja metalica de lo contrario se puede ocasionar un choque el&trico.

14. lnstalar

el panel

delantero.

Sacar 10s 2 tornillos

del panel

delantero que estan en la base del artefacto. Volver a

colocar

el panel

delantero

empujandolo derecho

y luego

haciendolo descender ligeramente para que se trabe en su lugar. Sujetar la parte inferior del panel delantero volviendo a insettar 10s 2 tornillos de la base. Ver Figura 30.

15.Calafatear todas las aberturas de la pared exterior alrededor de la instalaci& y de la caja met8lica.

16.lnstalar moldura decorative. Si se desea, instalar moldura alrededor de la caja metalica por el lado de la habitation.

24

Page 24
Image 24
Whirlpool ACM184XA0 manual Delantero que estan en la base del artefacto. Volver a, Colocar El panel Delantero, Luego

ACM184XA0 specifications

The Whirlpool ACM184XA0 is a sophisticated kitchen appliance designed to enhance cooking efficiency and versatility. Built with modern technology and a sleek design, this appliance stands out for its innovative features.

At the core of the ACM184XA0 is a high-performance induction cooking system that offers rapid cooking times and precise temperature control. Induction cooking heats up cookware directly through electromagnetic energy, ensuring that heat is generated only when suitable cookware is placed on the surface. This significantly reduces cooking time, making it a perfect option for busy households.

One of the notable features of the Whirlpool ACM184XA0 is its intuitive touch control panel, which provides easy access to a range of cooking functions. Whether you're simmering sauces, frying, or boiling, the interface allows for quick adjustments to settings with a simple touch. The appliance also includes multiple cooking zones, each with varying power levels, accommodating pots and pans of different sizes.

Safety is a primary consideration in the design of the ACM184XA0. The appliance is equipped with features such as auto shut-off and pan detection, which ensures that the induction element is only activated when suitable cookware is present. This not only prevents accidents but also enhances energy efficiency, making the cooking process more environmentally friendly.

In addition to its performance features, the Whirlpool ACM184XA0 boasts a sleek, modern aesthetic that fits seamlessly into any kitchen décor. Its minimalist design, complemented by a smooth glass surface, is not only visually appealing but also simplifies cleaning.

This induction cooktop also incorporates an innovative heat control feature, allowing users to maintain a steady temperature, which is ideal for melting chocolate or preparing delicate sauces. Furthermore, the appliance's rapid heat-up function ensures that cooking is not only efficient but also enjoyable.

With its combination of advanced technology, user-friendly controls, and stylish design, the Whirlpool ACM184XA0 is ideal for both novice cooks and seasoned chefs. It embodies the perfect blend of functionality and aesthetics, making it a valuable addition to any modern kitchen. Whether you're whipping up a weekday dinner or hosting a weekend gathering, this induction cooktop is designed to meet all cooking needs with ease.