EN Air Conditioner Use
Operating your air conditioner properly helps you to obtain the best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
•If you turn the air conditioner off and then turn the unit back on, the fan will come on, but the compressor will remain off for 3 minutes before turning back on. This prevents the air conditioner from blowing a fuse or tripping a circuit breaker.
•Do not try to operate your air conditioner in the cooling mode when outside temperature is below 65°F (18°C). The inside evaporator coil will freeze up, and the air conditioner will not operate properly.
Starting your air conditioner
Press Power ON/OFF to turn on air conditioner. When the unit is turned on, it will display the previous settings for the MODE, FAN SPEED and temperature.
TEMPERATURE SELECTION Press▲ to raise the temperature. Each time you press or hold▲, the temperature will go up 1° until it reaches 86°F (30°C).
Press▼to lower the temperature.
Each time you press or hold▼, the temperature will go down 1° until it reaches 64°F (18°C).
MODE SELECTION
Press MODE until you see the indicator light come on for the setting you want. Choose AUTO, COOL, FAN or POWER SAVER.
AUTO – Cools room while it automatically
controls fan speed. You cannot change fan speed, but you can adjust temperature by pressing▲or▼.
COOL – Cools room. You can select fan speed by pressing FAN SPEED. You can then adjust temperature by pressing ▲or▼.
FAN – Fan runs on TURBO speed only. Only the fan runs. Display shows “FO” (fan only).
POWER SAVER – Fan and compressor run only when cooling is needed. Fan stops running when the room temperature matches the temperature you set.
Press FAN SPEED until you see the indicator light for the setting you want. Choose TURBO, HIGH
or LOW.
Select the temperature by pressing▲or▼.
FAN SPEED SELECTION
NOTE: FAN SPEED button will operate only when COOL or POWER SAVER mode has been selected.
Press FAN SPEED until you see the indicator light for the setting you want. Choose TURBO, HIGH or LOW.
TIMER DELAY |
| |
The TIMER can be set for a 1 to 24 hour |
| |
delay until the air conditioner turns on or off. | ADJUST | |
Press▲or▼to adjust the delay time. | ||
| ||
To set the TIMER delay to turn the air |
| |
conditioner off, air conditioner must be in the |
| |
ON mode. |
| |
Press TIMER. (Indicator light will flash.) | TIMER | |
Press▲or▼to change delay time (1 to 24 |
| |
| ||
hours). |
|
Press TIMER or wait 10 seconds. (Indicator light will remain on.)
To set the TIMER delay to turn the air conditioner on, air conditioner must be in the OFF mode.
If you want to change the previous settings:
Turn air conditioner on.
Adjust MODE to AUTO, COOL, FAN, or POWER SAVER. Adjust FAN SPEED to TURBO, HIGH or LOW.
Adjust TEMPERATURE between 64°F (18°C) and 86°F (30°C).
Turn air conditioner off.
Press TIMER. (Indicator light will flash.)
Press▲or▼ to change delay time (1 to 24 hours). Press TIMER or wait 10 seconds.
If you want to keep the previous settings:
Turn air conditioner off.
Press TIMER. (Indicator light will flash.)
Press▲or▼to change delay time (1 to 24 hours). Press TIMER or wait 10 seconds.
To clear TIMER delay program, press and hold TIMER for 3 seconds. Indicator light will shut off. Air conditioner can be either on or off.
To see the remaining time (in hours), press TIMER once after it has been programmed. While the display is showing the remaining time, you can press▲ or▼to increase or decrease the time.
8
