9.Attach cabinet to finish frame. Drill 4 holes on each side and 2 holes in the top of the cabinet into the finish frame. Use #lO x 1” (25 mm) wood screws to attach cabinet to the frame. See Figure 26.

IMPORTANT: Do not overtighten screws or the cabinet will distort and provide a poor air seal between the cabinet and the air conditioner.

10.Place the 2%” (63.5 mm) seal strip (J) inside the cabinet. Make sure the seal is flush with the cabinet front edge. See Figure 27.

NOTE: This seal strip fits between the air conditioner base and the cabinet.

11.Insert drain cup (T). Place drain cup through hole in cabinet rail. See Figure 28.

12.Insert air conditioner into cabinet.

13.Reattach ground wire with grounding screw. Put excess grounded wire between the coils and the cabinet.

Electrical Shock Hazard

Air conditioner ground wire must be attached to the cabinet.

Failure to do so could result in electrical shock.

14.Attach the front panel. Remove the 2 front panel screws from unit base. Replace front panel by pushing it straight on and then lowering it slightly to lock it in place. Attach bottom front of panel by reinserting the 2 front panel screws. See Figure 29.

15.Caulk all outside wall openings around the installa- tion and cabinet.

16.Install decorative molding. If desired, install molding around room side of cabinet.

9.Colocar la caja metalica en el marco de acabado. Taladrar 4 agujeros a cada lado y 2 a traves de la parte superior de la caja metalica hacia el marco. Usar 10s tornillos de madera #lO x 25 mm (1”) para sujetar la caja metalica al marco. Ver Figura 26.

IMPORTANTE: No apretar demasiado 10s tornillos pues la caja metalica se deformara y no obturara bien el aire entre la caja metalica y el acondicionador de aire.

10.Colocar la cinta obturadora de 63,5 mm (2.5”) (J) dentro de la caja metalica. Asegurarse de que la cinta obturadora este al ras con el borde delantero de la caja metalica. Ver Figura 27.

NOTA: Esta cinta obturadora calza entre la base del acondicionador de aire y la caja metalica.

11.lnsertar la taza de drenaje (T). Colocar la taza de drenaje a traves del agujero en el travesaho de la caja. Ver Figura 28.

12.lnsertar el acondicionador de aire en la caja metalica.

13.Volver a instalar el alambre de puesta tierra en el tornillo de puesta tierra. Colocar el exceso del alambre de puesta a tierra entre 10s serpentines y la caja metalica.

El alambre de puesta a tierra del acondicionador de aire debe ser conectado a la caja metalica de lo contrario se puede ocasionar un choque electrico.

14. lnstalar el panel delantero. Sacar 10s 2 tornillos del panel

delantero que estan en la base del artefacto. Volver a colocar el panel delantero empujandolo derecho y luego haciendolo descender ligeramente para que se trabe en su lugar. Sujetar la pane inferior del panel delantero volviendo a inser-tar 10s 2 tornillos de la base. Ver Figura 29.

15.Calafatear todas las aberturas de la pared exterior alrededor de la instalacion y de la caja metalica.

16.lnstalar moldura decorativa. Si se desea, instalar moldura alrededor de la caja metalica por el lado de la habitation.

24

Page 23 Page 25
Page 24
Image 24
Whirlpool AR1800XA0 manual
Page 23 Page 25

AR1800XA0 specifications

The Whirlpool AR1800XA0 is a standout product in the world of modern kitchen appliances, particularly designed to meet the demands of today's busy households. This machine combines innovative technology with user-friendly features, making it a perfect choice for both cooking enthusiasts and everyday users.

One of the defining characteristics of the Whirlpool AR1800XA0 is its spacious capacity. With a generous interior, it provides ample room to accommodate various meal sizes, making it ideal for families or individuals who enjoy hosting gatherings. The appliance ensures even heat distribution, achieved through its advanced cooking technology, which guarantees that every dish is cooked thoroughly and evenly.

Another significant feature of the Whirlpool AR1800XA0 is its versatile cooking modes. Users can easily select from a range of preset functions to prepare a variety of dishes, including baking, grilling, steaming, and reheating. This versatility not only saves time but also allows for creativity in the kitchen, as it can handle a wide range of recipes.

In terms of convenience, the Whirlpool AR1800XA0 boasts an intuitive control panel and a user-friendly interface. This design simplifies the cooking process, allowing users to set their desired temperature and timer with ease. Additionally, the appliance comes equipped with a smart sensor technology that automatically adjusts cooking times and temperatures based on the food type, ensuring optimal results every time.

Energy efficiency is a core consideration in the design of the Whirlpool AR1800XA0. This model is engineered to consume less power without compromising on performance, making it an eco-friendly choice for environmentally conscious consumers.

Durability is another hallmark of the Whirlpool AR1800XA0. Built with high-quality materials, it is designed to withstand daily use and is easy to maintain, ensuring that it remains a staple in the kitchen for years to come.

Safety features are also prioritized in this appliance. The Whirlpool AR1800XA0 includes an automatic shut-off function and cool-touch handles, which provide peace of mind during operation.

In summary, the Whirlpool AR1800XA0 is a versatile, efficient, and user-friendly kitchen appliance that combines modern technology with practical features. Its spacious capacity, range of cooking modes, energy efficiency, and safety features make it an excellent investment for anyone looking to enhance their cooking experience.
Top Page Image Contents