To check the actual | and set temperatures: |
| |||
| 1. Press the FRZ TEMP or REF TEMP Pad. | ||||
!l!l | The signal light on the pad you | ||||
pressed |
| and the ACTUAL | signal | light | |
q | will come on. The actual refrigerator | ||||
or freezer | temperature | will be | dis- | ||
played. | (This is the average air tem- | ||||
| perature |
| in the compartment.) |
|
2. Press the SETTEMP Pad. The SETsignal
wlight will come on and the set tem- perature will be displayed. You may set freezer temperatures from 5°F
frigerator temperatures from
NOTE: If the actual freezer temperature is above the display range, a flashing 8 will show on the
display. If the actual refrigerator temperature is above the display range, a flashing 42 will show on the display.
To change the refrlgerafor or freezer temperatures:
The refrigerator and freezer temperatures are preset at 36°F (2”CJ and 0°F
1.Press the FRZ TEMP or REFTEMP Pad. The signal light on the pad you
Eu | pressed | will | come | on | and the |
| actual | refrigerator | or | freezer | |
| temperature | will be | displayed. |
2.Press the SETTEMP Pad The SETsia- nal light will come on and the pr& set temperature will be disptayed.
A | 3. Press the A Pad to raise the tem- | |||
0 | perature setting or press the V Pad | |||
to lower | the | temperature | setting. | |
| You must press these pads within IO | |||
Hi | seconds of pressing the SETpad or | |||
you will | have | to press SETagain. |
NOTE: Two beeps will sound to indicate an error
if you attempt to set a temperature past the re-
frigerator or freezer temperature range.
Two beeps will sound to indicate an error if you press the arrow pads without pressing the SET pad.
To return to preset temperatures (AUTO TEMP): i. Press the AUTO TEMP Pad.
2.The signal light will come on for IO seconds to show that the tem- perature has been set, then the light will turn off.
Using AUTO TEMP will set the freezer temperature to O’F ( - 18°C) and the refrigerator to 36°F (2°C).
To set MAX FRUICE and MAX REFICOOL:
The MAX FRZ/ICE Pad will set the freezer
compartment can be set independently for max- imum cooling. MAX FRZ/ICE can also be used for maximum ice production. After 24 hours, the tem- peratures will return to the earlier settings.
1.Press the MAX FRZ/ICE or MAX REF/COOl Pad. The signal light on the pad you pressed will come on.
Pad. -
NOTE: Each time you press a maxlmum cooling pad a new 24 hour cycle will start.
Electronic display warning signals...
The five signal lights on the right side of the Elec- tronic Control Center will show if an action is needed or if there is a problem.
DOOR AJAR (red flashing light)
l The DOOR AJAR light flashes when either door is open.
. Eight beeps sound when either door is open for longer than 3 minutes. Beeps are heard every 2 minutes until door(s) are closed.
WARM (red flashing light)
l The WARM light flashes when the refrigerator and/
or freezer temperature(s) are above 48,‘F/15’F (9”C/ - 9°C).
l Eight beeps sound every 2 minutes.
l The FRZ TEMP and/or REF TEMP signal light(s) will
also flash to show which compartment is too warm.
l Open compartment door(s) less often. Check the set temperatures.
WARM (red light)
l The WARM light is on when refrigerator and/or
freezer temperature(s) were above 48”F/15”F (9”C/ - 9°C) but are now in a safe temperature range.
l The FRZ TEMP and/or REF TEMP signal light(s) will
also stay on to show which compartment was too warm.
l The signal lights can be turned off by pressing the RESETPad.
CHECK FOOD (red flashing light)
l The CHECK FOOD light flashes when refrigerator and/or freezer are above safe temperature(s) and have been for 4 hours or more.
. The WARM, FRZTEMP and/or REFTEMP signal lights will also flash.
l Check food for spoilage. Check the set temperature.
* Call for service, if necessary.
6