Remove the Doors
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1.Unplug refrigerator or disconnect power.
2.Open both doors (refrigerator and freezer) and the water filter cover door. It is not necessary to remove the water filter itself.
3.Remove the base grille by pulling up on the bottom outside corners. See Graphic 1.
4.Disconnect the water dispenser tubing located behind the base grille on the freezer door side. The dispenser tubing runs through the door hinge, and must be disconnected in order to remove the door. See Graphic 2.
■Press blue outer ring against the face of fitting and pull the dispenser tubing free.
NOTE: Keep the water tubing connector attached to the tube that runs underneath the freezer. The door cannot be removed if the connector is still attached to the tube that runs through the door hinge.
5.Disconnect the wiring located behind the base grille on the freezer door side. See Graphic 3.
■Remove the wiring clip using a ¹⁄₄"
■Disconnect wiring plugs.
6.Close both doors and keep them closed until you are ready to lift them free from the cabinet.
7.Use a ⁵⁄₁₆"
IMPORTANT: Do not remove either screw A.
8.Lift freezer door straight up off bottom hinge. See Graphic 5. The water dispenser tubing and wiring remain attached to the freezer door and pull through the bottom left hinge.
NOTE: This may require two people - one to lift the door and another to feed the water tubing and wiring through the hinge.
IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door, water tubing and wiring.
9.Remove top right hinge as shown. See Graphic 6. IMPORTANT: Do not remove either screw A.
10.Lift the refrigerator door straight up off bottom hinge.
IMPORTANT: Rest the door on its side on a soft, clean surface, such as a towel, blanket or piece of cardboard. This will help avoid damaging the door.
11.It may not be necessary to remove the bottom hinges to move the refrigerator through a doorway. Both bottom hinges have similar construction.
■If necessary, disassemble the hinges as shown. See Graphic 7.
IMPORTANT: To aid in door alignment and closing, there is a shim located between the hinge and the cabinet. When the hinge is removed, the shim may fall out of place. If this occurs, set the shim aside so it can be put back in place when the hinge is reconnected later.
Replace the Doors and Hinges
1.Replace both bottom hinges, if removed. Make sure the shim is between the hinge and cabinet. Tighten screws.
2.Before replacing the freezer door on the bottom left hinge, feed the wiring with the yellow plug and the water dispenser tubing through the hinge. Assistance may be needed.
NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.
3.Align and replace the top left hinge as shown. See Graphic 4. Tighten screws.
4.Reconnect water dispenser tubing and wiring.
IMPORTANT: Do not intertwine the water tubing and wiring bundles when reconnecting them.
■Push tubing into fitting until it stops and the black mark touches the face of fitting. See Graphic 2.
■Reconnect wiring plugs. Reinstall the wiring clip over the grommets. Tighten screw. See Graphic 3.
5.Replace the refrigerator door by lifting the door onto the bottom right hinge.
6.Align and replace the top right hinge as shown. See Graphic 6. Tighten screws.
7.Replace the ice storage bin (on some models) and any adjustable door or utility bins.
8.Plug into a grounded 3 prong outlet.
Leveling and Door Closing
Your refrigerator has two front adjustable rollers — one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:
1.Move the refrigerator into its final location.
2.Remove the base grille to locate the two leveling screws, which are part of the front roller assemblies on each side. See Graphic 8.
NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.
3.Use a ¹⁄₂"
4.Open both doors again and check that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.
5.Use a bubble level to check the leveling of the refrigerator.
NOTE: Whenever you need to move the refrigerator, turn the leveling feet to the right until they are no longer touching the ground. This will allow the refrigerator to roll more easily.
5
