INSTALLATION INSTRUCTIONS

Prepare Location

■Lay out the vent duct system before installing the range hood to determine the best routing for the vent duct.

■It is recommended that the vent system be installed before the range hood is installed.

■Before making cutouts, make sure there is proper clearance within the ceiling for exhaust vent.

■Range hood is to be installed 24" (61.0 cm) min. for electric cooking surfaces, 27" (68.6 cm) min. for gas cooking surfaces, to a suggested maximum of 36" (91.4 cm) above the cooking surface.

■Remove film from metal surfaces as needed prior to assembly.

■Check your ceiling height and the range hood height maximum before you install your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface. Place two 3" (7.6 cm) high spacers (not included) onto the covered surface.

NOTE: Cover the spacers to avoid damage to the range hood surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered spacers.

2.Tape template in place on the ceiling at the marked centerline. The line for the front of the range hood should be parallel to the front of the cooktop.

3.Use a pencil to mark the mounting screws, wire access and duct hole locations on the ceiling.

NOTE: Mounting hole locations should be into a ceiling support structure capable of holding 80 lbs (36.6 kg).

Remove the template.

4.Drill 4 - ³⁄₁₆" (4.8 mm) pilot holes for mounting the upper horizontal support.

Complete Preparation

1.Determine the required location for the home power supply cable and drill a ½" (1.3 cm) diameter hole for wire access.

2.Run ½" (1.3 cm) conduit and wires or home power supply cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ½" conduit and wires or home power supply cable from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

3.For vented installations only: Using a jigsaw or keyhole saw, cut a 6½" (16.5 cm) diameter hole for the vent duct.

4.Attach the upper horizontal support bracket with 4 - 5 x 45 mm wood screws.

NOTE: Upper horizontal support screws must be into a ceiling support structure capable of holding 80 lbs (36.6 kg).

C

 

A

A

B

 

A. Covered spacers

 

B. Glass canopy

 

C. Ventilator assembly

 

Range Hood Mounting Screws Installation

A. Upper horizontal support

1.Determine and mark the centerline on the ceiling where the range hood will be installed, considering the requirements for ceiling support structures. See the “Location Requirements” section. Make sure the range hood is centered over the cooking surface.

7

Page 6 Page 8
Page 7
Image 7
Whirlpool LI31HC/W10526058F installation instructions Installation Instructions, Prepare Location, Complete Preparation
Page 6 Page 8

LI31HC/W10526058F specifications

The Whirlpool LI31HC/W10526058F is a state-of-the-art refrigerator that exemplifies modern design and advanced technology, making it an ideal addition to any contemporary kitchen. This model is recognized for its stylish aesthetics, energy efficiency, and innovative features that cater to the needs of every household.

One of the standout characteristics of the LI31HC is its spacious interior, designed to maximize storage while maintaining an organized layout. With adjustable shelves and humidity-controlled crispers, users can customize the configuration to accommodate various food items, from large platters to delicate produce. The refrigerator boasts a generous capacity, ensuring ample space for groceries and leftovers.

Energy efficiency is a pivotal aspect of the Whirlpool LI31HC/W10526058F. With an impressive Energy Star certification, this refrigerator not only helps to reduce utility bills but also minimizes environmental impact. The appliance features advanced insulation and efficient cooling systems that work together to maintain optimal temperatures, ensuring food stays fresh for longer periods.

Whirlpool’s commitment to innovation is evident in the incorporation of adaptive cooling technology. This feature allows the refrigerator to monitor internal conditions and adjust cooling settings accordingly, maintaining the freshest environment for food storage. The frost-free design is another key benefit, eliminating the need for manual defrosting and providing hassle-free maintenance.

Another notable technology integrated into the LI31HC is the advanced filtration system. This ensures that both water and ice are purified for safe consumption, providing peace of mind for families who prioritize health and wellness. The sleek ice maker is conveniently located, ensuring easy access without compromising the refrigerator's design.

In terms of usability, the LI31HC/W10526058F includes intuitive controls, making it simple to customize settings to suit individual preferences. The LED lighting inside provides brilliant visibility, allowing users to easily find items even in low-light conditions.

Overall, the Whirlpool LI31HC/W10526058F combines functionality with modern aesthetics, making it a remarkable choice for those seeking a reliable and stylish refrigerator. Its advanced features cater to the needs of today's consumers, making food storage a seamless experience. Whether you're preparing a family meal or hosting friends, this refrigerator is equipped to handle it all with grace and efficiency.
Top Page Image Contents