Whirlpool Microwave Range Before you start, Electrical requirements, Mobile home installation

Before you start...

Proper installation ISyour tesponslbtllty

A qLallf(ed lechnlclan should Install this range Make sure you have everythIng necessary for correct lnstallatlon It 1s the responslblllfy of the installer to cornply with the lnstallatlon clearance specified on the serlal/ratlng plate The ser~al/ratlna alate 1slocaled behlnd the mlcrov&e oven door on the front frame of the microwave oven

Rerrove all aackaalna- - maierla from microwave over cavity Check the over area for damoge- see For Your Safety If any damage ISevident do not operate microwave over until 11ISchecked by

outhorlred WhIrlpool seruce technicIan

NOTE: Clearances specified ore for combustible wall and materials that have Q density of 20 or more pounds per cubic foot. No evaluation of clearances has been mode for instollotions adjacent to materials that ore less than 20 pounds per cu. ft. or to plostlc tiles and sheeting.

Tools needed for installation.

Mobile home installation

The installation of this ranae must

conform to the Manufact&d Home Construction and Safety Standards, Title 24 CFR. Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, par-l 2801.

Four-wire power supply cord must be used and the appliance wiring must be revised See Electrical requirements,

When this range is installed in a mobile home, it must be secured to the floor durrng transit. Any method of securing the range is adequate as long as it conforms to the standards listed above

Copies of the standards listed may be obtained from:

*National Fire Protectton Asscclatlan

Ratterymarch Pork

Qulncy, Massachusetts 02169

Electrical requirements

IMPORTANT:

Save Installation Instructions for the local electrical Inspector’s use.

A power supply cord Is not supplled with this appliance but is available through your local electrical supply houses.

Cabinet opening dimensions that are shown must be used Given dimensions are mlnimum clearances and provide required V clearance.

*,,.,1,

Grounded elo-‘-‘--I outlet is requircu. ~xi= Electrical requirements.

Important: Observe all crovernina codes and ordinanck.

Electrical Shock Hazard

l Electrlcal ground Is required on thts appliance.

l tmproper connection of the equlpment-groundlng conductor can result In electrical shock.

. Check wlth a quallfled electriclan If you are in doubt as to whether the appliance Is properly grounded.

l Only a power supply cord klt rated at 240 volts, 50 amperes and lnvestlgated for use wlth ranges shall be used.

l Do Not use an extension cord wlth thls appliance. Such use may result In a fire, electrical shock or other personal Injury.

lDo Not have a fuse in the neutral or graundlng clrcult. A fuse In the neutral or grounding clrcult could result In electrlcal shock.

l Do Not plug the ‘pigtall” power cord into a-live receptacle before the cord Is permanently connected to the terminal block. To do so may result In electrical shock.

Failure to follow these instructions could result In an electrtcal shock.

	This appliance	mud be
A n Connected to the proper
electrical	voltage and frequency as
specified	on the &al/rating	plate. All

models require a separate 50 amp circuit. Fuse both sides of the line. Do Not fuse the neutral. A time-delay fuse or circuit breaker Is recommended. Check the serial/rating plate located behind the mIcrowaG oven door on the front frame for the required voltage and frequency

B It is the personal responsibility w and obligation of the customer

to contact a qualified electrlclan to assure that the electrlml installation is adequate and is in conformance with

Personal Injury Hazard

It Is the customer’s responslbllitv:

. To contact a qualified electrical Installer.

. To assure that electrlcal installation Is adeauate and in conformance wlth’lrlatlonal Electrlcal Code, ANSllNFPA 70. latest editlon: and local ordinances.

Failure to follow these Instructions could result in an electrical shock.

l Cabinet storage above the cooklng surface should be

avolded

Reaching over a heated cooklng surface could result In a serious burn.

l Do not attempt to operate the microwave oven wlth the door open.

l Do not tamper wlth or defeat the safety Interlocks.

l Do not place objects between the microwave oven front face and door.

. Da not allow sol1 or cleaner residue to accumulate on sealing surface of the mlcrowave oven door.

. Da not operate the mlcrowave oven If damaged.

. Do not use the mlcrowave oven If

-door Is bent.

-hlnges and latches are broken or loose.

-door seals, sealing surfaces or alass are broken.

The mlcmwave oven door must close properly to pmvlde safe operatlon.

l Only have a quallfled repair person adjust. repalr and check microwave oven for mlcmwave leakage after a repalr Is made.

. Do not use mlcmwave for commercial purposes.

The mtcmwave oven In thls unlt Is

to follow these lnstructlo~s could result In exposure to excessive mlcmwave energy.

the National Electrical Code ANSVNFPA 70.latest edition,’ and local codes and ordinances.

All wires ending at the C appliance must terminate in

W ring type terminals.

3.WIrewall

mmPtac*

(10.5011) Figure 1

D Local codes may permit the n use of a three-wire. flexible-type.

U.L.-listed power supply cord (pigtailj with the proper ampere rating. This cord contains three. No.-10 copper wires and matches a three-wire receptacle of NEMA typelo-5OR. shown in Figure 1. A U.L.-listed strain relief must be provided at the point the power supply cord enters the appliance.

E The range may be connected

. directly to the fused disconnect (or cirwit breaker) box through

flexible, armored or non-metallic sheathed, copper cable. Allow at least 4 feet mlnlmum slack in the line between the wall and the appliance so that it can be moved if servicing is ever necessary A U.L.-listed stmin relief must lx provided at each end of the power supply cord. NIB sizes [COPPER WIRE ONLY] and connectors must axlform with the rating of the appliince as specified on the serial/mtlna -.plate.

F THERANGE MU!3 BECONNECTED W WllH COPPER WtREONLY.

For mobile home or other four- G wire Installations. the

n appliance wlrtng must be

Ponet A