Whirlpool Microwave Range Kwlre electrical connection, 3v&y-&i+sI, Push in and turn

the broil element. Set the oven

seledor and oven temperature control knobs to “BROIL:‘Thetoo element should glow red and Indicate light should beon.

kwlre electrical connection

11.

nd

Use a U.L.-listed strain relief

nand Insert it into the hole below the terminal block. Insert the paver cord through the strain relief allowing enough slack to easily attach to terminal block.

:

t---.-

13 Remove cover from appro-

nprtate vent opening in hcod

(roof of wall ventinat.

- -’ Gs---7-?I

‘1’ T CenLneIII

14. Determine and clearly mark a vertical centerline in

the area the vent opening will be made.

TOY&~ thr&gh the roof. jd mark on the underside of

the cabinet IYz” in from back wall. Measure and mark a line 5’to right and left of the centerline Then measure W” towards the front of the cabinet and mark onother line as before. Use a saber saw to cut a rectangular opening for ductwork. The opening must be large enough to fit 3Y4”x lo” duct system.

To vent through the wall, measure from the floor 71” and 67%” and mark on the back wall. Measure and mark a line 5” to right and left of the centerline at both heights. Use a saber saw to cut a rectangular opening for ductwork The opening must be large enough to fit 3Y4”x IO” duct system.

3v&y-&i+sI__- ---__/

I

16 Install duct through the vent W opening In the upper

cabinet or wall. Complete the venting system according to the method needed See Venting requirements. Use caulking to seal exterior wall or roof opening around exhaust hood.

17---Attach=-damper to selected n vent opening. If damper IS attached to the back of hood, be sure

damper hinge is toward the top,

Panel C

Floor Damage

Keep cardboard shipplng piece under range.

FoIlurn to do so could cause damage to floor coverlng.

Move range close to cabinet n ODenina. Remove cardboard

shipping piece from under ranae Careful& move range into cab:net openina and center. Connect ductwork to range hood

ace rack in oven. Place Vet on rack, first side to side then front to back. If the ranae is

not level, remove storage drawerthen screw the legs up or down to adjust.

Note: Oven must be level for satisfactory baking conditions,

20 n Push in and turn

knob to “HI”posttion. Check the operation

of the ccoktop elements and indicator lights

*1.72

21 Check the operation of the n oven element. Set the oven selector control knob to “BAKE:‘Setthe

oven temperature control to XW.The bottom element should glow red and the indicator light should be on The upper element should become hot but not glow redThe oven indicator light goes off when oven ISpreheated

the grounding screw.Bend up the grounding link so that It does not contact the range.

LA--

C Connect the green grcunding W wire to the range using the

grounding screw removedmustIn Step B.The

green grounding wire be attached ;;tmi~lmust not contact any other

&nect the neutral (white]

Iwire to the center silvercolored terminal screw on terminal block. Connect the other two wires to the outer terminals on the terminal block. Use rirg- Npe terminals only Connect the brass nuts that am taped to the tram-e. Do Not kznsen factory installed nuts already on the terminal. Be sure that the nuts are installed tight.

E Tighten the strain relief screws. n Replace access panel.

WhMpoolmlcmwaveeys-kvel mnQ0.10getthernaslonktentuae homyourmwrange.roodpur

range far easy mfemnce. me lmhuc. tloru will make mlrutalllng your WMtpool range In another

llameasoasyaafhe nd Installation.