Whirlpool SC864OED Before you start, Product Dimensions, Cabinet and Cutout, Clearance

Before you start...

Proper installation is your responsibility, Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the model/serial rating plate. The model/serial rating plate can be found on the underside of the cooktop burner box. Write down your cook-top model and serial numbers before installing cook-top. You will be asked for these numbers if you need to call for service or assistance.

Note: This cookfop is manufactured for use with Natural gas. To convert for use with L.F?/Propane gas requires Kit No. 4173631, available from your Whirlpool dealer or authorized parts distributor.

Product Dimensions

Burner box helght - 2-J/4”

30” mln. base cabinet is required. If cabinet has a drawer, a 3” depth clearance from \ the countertop to the top of the drawer (or other obstruction) in base cabinet is required.

This cooktop is not approved for use with downdruft vent systems.

Check location where cook-top will be installed. The location should be away from strong draft areas, such as windows, doors and strong heating vents or fans. The cooktop should be located for convenient use in the kitchen.

ALL OPENINGS IN THEWALL OR FLOOR WHERETHECOOKTOP ISTO BE INSTALLEDMUSTBESEALED.

-7%

Grounded electrical outlet is required. See “Electrical requirements.”

Proper gas supply connection must be available. See “Gassupply requirements.”

Countertop opening dimensions that are shown must be used. Given dimensions provide required 0” clearance.

Important: Observe all governing codes and ordinances. Failure to meet codes and ordinances could lead to fire or electrical shock.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

- Do Not store or use gasoline or
other flammable		vapors and
liquids in the vicinity of this or
any other	appliance.
- WHATTO DO IFYOU SMELL GAS
l Do Not try to light any
appliance.
l Do Not touch any electrical
switch; Do Not use any phone
in your building.
l Immediately call your gas
supplier	from	a neighbor’s
phone. Follow		the gas
supplier’s	instructions.
l If you cannot reach your gas

Cabinet and Cutout		Dimensions
			30”	mln
	p-		:E:::k:p	-
1” min.	space
between	adjacent		distance
cookiops	Minimum			13” max.	Y
	to	nearest	rear
				-upper
	combustible surface			cabinet	\
	above cooktop			depth

supplier, call the fire

department.

- Installation and service must be

performed by a qualified installer,

service agency or the gas

Isupplier.

Fire Hazard

\I	2-l/4”		\
		mln.
	space	to	front
	edge	of	c&net

Wall aas line /

--

I

Do Not obstruct the flow of combustion and ventilation air.

Injury Hazard

To eliminate the risk of burns or fire, avoid installing cabinet storage above the cooking surface. If cabinets are already installed, reduce the hazard of reaching over a heated cooking surface by installing a range hood. The range hood should extend a minimum of 5 inches out

Important: Observe all governing codes and ordinances.

Failure to meet codes and ordinances could lead to fire or electric shock.

5” below count&on
and centered	In
cabinet.	I	Centerline	01	I I
	! /wall	and	unlt

Do Not pinch the power supply cord between the cooktop and cabinet.

from the bottom front of the cabinets.

Reaching over a heated cooking surface could result in a serious burn or other injury.

Clearance	Dimensions
				l ** Note: 30” mln. when bottom 01
				wood or metal cabinet Is				l/4”
		I	I	Drotected		bv not	less than
				ilome retard’ant mlllboard				.
				covered wlth not less than No.
				28 MSG sheet steel, 0.0 15”
	See	Note***		stalnless		steel, 0.024” alumlnum
				or	0.020”	copper.
	for	mlnlmum		38’	mln. clearance		between the
	clearances.
				top of the cooklng plattorm and

the bottom of an unprotected wood or metal sheet.

	nearest	combustible
\	surface	above cookfop

Electrical Shock Hazard IIt is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that electrical installation is iadequate and in conformance with IUational Electrical Code ANSUNFPA 70 - Iatest edition* and all local codes and cordinances.

F-ailure to do so could result in death or !serious injury.

1rake special care when drilling holes into t he wall for electrical wiring. Electrical unrires may be concealed behind the wall c:overing.

F‘ailure to do so could result in death or zserious iniurv.

Copies of the standards listed may be obtained from:

‘National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

‘*American Gas Association 1515 Wilson Boulevard Arlington, Virginia 22209

Panel A