Manuals / Whirlpool / Kitchen Appliance / Range

Whirlpool UXT5230AYB, UXT5230AYS, UXT5236AYS Power Supply Cable Installation

Models: UXT5236AYS UXT5230AYB UXT5230AYS

1 32
Download 32 pages 50.34 Kb
Page 10
Image 10

NOTE: The 7" (17.8 cm) round vent mounting plate and

3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vent damper can be installed up to 1" (2.5 cm) on either side of the hood center to accommodate off-center ductwork.

B

A

C

D

E

C

B

A. Vertical vent connector with damper

B. 3.5 x 5 mm screws

C. Hinge pin

D. Vent knockouts

E. Horizontal vent connector with damper

■If a vent damper is installed with a wall cap with damper, check that they do not interfere with each other. Remove the vent connector damper flap if they interfere.

■Non-vented (recirculating) installations - No vent attachments. Removal of the recirculation cover plate is required. Remove the two screws from the recirculation cover plate and remove.

A

B

A. Recirculation cover plate

B. Screws

Power Supply Cable Installation

1.For direct wire installations, run the home power supply cable according to the National Electric Code or CSA standards and local codes and ordinances. There must be enough wiring from the fused disconnect (or circuit breaker) box to make the connection in the hood electrical terminal box.

For optional power supply cord kit installations, follow the instructions in the “Make Electrical Connection” section. See the “Accessories” section for information on ordering.

NOTE: Do not reconnect power until the installation is complete.

2.Remove the screw from the terminal box cover. Remove terminal box cover and set aside.

A

B

A. Terminal box cover

B.Screw

3.Remove the power supply knockout from the top or rear of the vent hood (depending on the incoming location of your home power supply cable) and install a UL listed or CSA approved ¹⁄₂" strain relief.

A

A. Power supply knockout

4.Using 2 or more people, lift the hood into final position. Feed enough electrical wire through the ½" UL listed or CSA approved strain relief to make connections in the terminal box. Tighten the strain relief screws.

5.Position the range hood so that the large end of the keyhole slots are over the mounting screws. Then push the hood toward the wall so that the screws are in the neck of the slots. Tighten the mounting screws, making sure the screws are in the narrow neck of slots.

6.Connect ventwork to hood. Seal joints with vent clamps or duct tape to make secure and airtight.

7.Check that back draft dampers work properly.

10

Page 9 Page 11
Page 10
Image 10
Whirlpool UXT5230AYB, UXT5230AYS, UXT5236AYS installation instructions Power Supply Cable Installation
Page 9 Page 11

UXT5236AYS, UXT5230AYB, UXT5230AYS specifications

The Whirlpool UXT5230AYS, UXT5230AYB, and UXT5236AYS are three highly regarded under-cabinet range hoods that blend contemporary design with cutting-edge technology, aiming to enhance the efficiency and aesthetics of modern kitchens. Each model is designed to provide powerful ventilation while maintaining a streamlined appearance, complementing various kitchen styles.

One of the standout features of these range hoods is their robust airflow capacity, which effectively removes smoke, odors, and steam produced while cooking. With a maximum CFM (cubic feet per minute) rating of 190, these models ensure that your kitchen remains fresh and free from lingering smells. The adjustable fan speeds offer the flexibility needed to match the ventilation power with the intensity of your cooking, ensuring optimal performance for both light and heavy-duty culinary tasks.

The UXT5230AYS and UXT5230AYB models come equipped with a convenient push-button control system. This user-friendly interface makes it easy to adjust fan speeds and turn the hood's lights on and off, providing hassle-free operation while cooking. Additionally, the UXT5236AYS features similar controls but with an enhanced design aesthetic to cater to various consumer preferences.

Lighting is crucial in the kitchen, and these range hoods do not disappoint with their bright, energy-efficient LED lighting. This lighting casts a clear beam over your cooking surfaces, making food preparation safer and more enjoyable. The longevity of LED lights minimizes the need for frequent replacements, making these hoods a cost-effective choice in the long run.

Maintenance has been simplified as well, with stainless steel baffle filters that are both durable and easy to clean. These filters capture grease effectively while adding a sophisticated touch to the hood’s design. They are dishwasher safe, allowing for effortless cleaning without the risk of damage.

In terms of installation, the UXT5230AYS and UXT5230AYB models have a slim profile, making them ideal for kitchens with limited space. Each unit is designed to fit comfortably under cabinets while providing sufficient coverage over cooking surfaces.

Overall, the Whirlpool UXT5230AYS, UXT5230AYB, and UXT5236AYS range hoods stand out in terms of performance, design, and functionality. They are excellent choices for homeowners looking to enhance their kitchen's ventilation and overall efficiency while enjoying the benefits of modern technology and stylish aesthetics.