To Throw Snow, Operating Tips | White Outdoor 772C0715 specification

Auger Control Test

IMPORTANT: Perform the following test before operating your snow thrower for the first time and at the start of each winter season.

Check the adjustment of the auger control as follows:

•When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

•In a well-ventilated area, start the snow thrower engine as instructed earlier in this section under the heading Starting the Engine. Make sure the throttle is set in the FAST position.

•While standing in the operator’s position (behind the snow thrower), engage the auger.

•Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

•With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine.

•Confirm that the auger has completely stopped rotating and shows NO signs of motion.

IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

•To readjust the control cable, loosen the hex jam nut on the auger control cable “Z” fitting.

•Rotate the coupling end of the cable (without turning the cable) counterclockwise to provide more slack.

•Retighten the hex jam nut. See Figure 11.

•Repeat Auger Control Test to verify proper adjustment has been achieved.

To Throw Snow

CAUTION: Check the area to be cleared for foreign objects. Remove, if any.

1.Start the engine following starting instructions.

2.Rotate the discharge chute to the desired position, (away from bystanders and/or buildings) by moving the chute control.

3.Select the speed according to snow condition.

CAUTION: Never move the shift lever without first releasing the drive clutch.

4.Engage the auger control and drive control levers as previously stated.

Z Fitting

Hex Nut

Cable Should

Be Straight

Figure 11

5.The interlock feature will allow you to remove your left hand from the auger control lever.

6.When clearing the first pass through the snow, control speed of snow thrower according to the depth and condition of snow.

7.On each succeeding pass, readjust the chute to the desired positon and slightly overlap previous path.

8.After the area is cleared, stop the snow thrower following instructions given below.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of muffler and

surrounding areas may exceed 150o F. Avoid these areas.

•For most efficient snow removal, remove snow immediately after it falls.

•Discharge snow downwind whenever possible. Slightly overlap each previous swath.

•Set the skid shoes 1/4" below the scraper bar for normal usage. The skid shoes may be adjusted upward for hard-packed snow.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

•If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between ground and shave plate.

•Clean the snow thrower thoroughly after each use.

772C0715 specifications

The White Outdoor 772C0715 is a notable powerhouse in the realm of outdoor lawn equipment, specifically designed for those who seek efficiency and convenience in their gardening tasks. Built with robust engineering and user-friendly features, this model stands out in the market.

One of the core aspects that define the White Outdoor 772C0715 is its powerful engine. It typically comes equipped with a reliable gas engine that delivers smooth operation and ample power to handle a variety of yard maintenance tasks. The engine's design focuses on providing exceptional torque, allowing users to tackle thick grass and challenging terrain without sacrificing performance.

The cutting deck on the 772C0715 is designed for precision and efficiency. Featuring a wide cutting path, it ensures that the user can cover large areas in a short amount of time. This model often incorporates adjustable cutting heights, which enables users to customize their mowing experience according to the specific needs of their lawn. Whether it’s a manicured garden or a more rugged area, the versatility in cutting height helps achieve the desired results.

Another significant feature is its user-friendly controls. The 772C0715 often integrates intuitive controls that allow users, regardless of their experience level, to operate the machine with ease. Simple functions for starting, stopping, and adjusting settings can significantly enhance the overall mowing experience.

Moreover, the design of the 772C0715 emphasizes comfort during operation. Many models come with ergonomic handles that reduce strain on the operator, especially during prolonged use. The lightweight construction further aids in maneuverability, allowing users to navigate around obstacles without difficulty.

The White Outdoor 772C0715 also showcases advanced durability through its construction materials. Engineered to withstand the test of time, its components resist wear and tear, making it a sound investment for homeowners and professional landscapers alike.

In sum, the White Outdoor 772C0715 encapsulates practicality and performance in lawn care. With a powerful engine, adjustable cutting deck, user-friendly controls, and durable construction, it is designed to meet the demands of various gardening tasks while providing comfort and ease of use for every operator. Whether you are a seasoned gardener or just starting, the 772C0715 proves to be a valuable addition to any outdoor tool collection.

White Outdoor 772C0715 manual To Throw Snow, Operating Tips

Models: 772C0715

Auger Control Test

To Throw Snow

Operating Tips

772C0715 specifications