5 CHECK THERMOSTAT OPERATION

CONTINUED FROM FOURTH PAGE

11Flame icon () is displayed when the SYSTEM switch is in the HEAT position. Flame icon () is displayed flashing when 2nd-stage heat (Aux or Emergency) is energized. Snowflake icon () is displayed (non-flashing) when the SYSTEM switch is in the COOL position. Snowflake and Flame icon will be displayed (flashing) if the thermostat is in lockout mode to prevent the compressor from cycling too quickly.

12EMER is displayed flashing when the system switch is in EMER position.

13Alternately displays current time and temperature.

14The word HOLD is displayed when the thermostat is in the HOLD mode.

15Displays currently programmed set temperature (this is blank when SYSTEM switch is in the OFF position).

16“BATT” is displayed when 2 “AAA” batteries are low and should be replaced.

Configuration Menu

The configuration menu allows you to set certain thermostat operating characteristics to your system or personal requirements. Press RUN to make sure the thermostat is in the run program mode, then press PRGM and RUN at the same time to enter the configuration menu. The display will show the first item in the configuration menu.

The configuration menu chart summarizes the configuration options. An explanation of each option follows.

Press HOLD to change to the next menu item or press TIME to go backwards to the previous item in the menu. To exit the menu and return to the program operation, press RUN. If no keys are pressed within fifteen minutes, the thermostat will revert to normal operation.

1.In the run mode, if the setpoint temperature is manually raised by 3°F (2°C) or more above the actual temperature with the TEMPERATURE UP key, and the fast second stage feature is enabled, FA on, the second stage will energize immediately.

With FA off, second stage will not energize until the setpoint temperature is 1°F or more above actual temperature for more than ten minutes.

2.Select Compressor Lockout CL OFF or ON – Selecting CL ON will cause the thermostat to wait 5 minutes before turning on the compressor if the heating and cooling system loses power. It will also wait 5 minutes minimum between cooling

and heating cycles. This is intended to help protect the compressor from short cycling. Some newer compressors already have a time delay built in and do not require this feature. Your compressor manufacturer can tell you if the lockout feature is already present in their system. When the thermostat compressor time delay occurs it will flash the Snowflake and Flame icons for about five minutes.

3.Select Temperature Display Adjustment 3 LO to 3 HI – Allows you to adjust the room temperature display up to 3° higher or lower. Your thermostat was accurately calibrated at the factory but you have the option to change the display temperature to match your previous thermostat. The current or adjusted room temperature will be displayed on the left side

of the display.

Operating Features

Now that you are familiar with the thermostat buttons and display, read the following information to learn about the many features of the thermostat.

•SIMULTANEOUS HEATING/COOLING PROGRAM STOR- AGE — When programming, you can enter both your heating and cooling programs at the same time. There is no need to reprogram the thermostat at the beginning of each season.

•TEMPERATURE OVERRIDE — Press oruntil the display shows the temperature you want. The thermostat will override current programming and keep the room tempera- ture at the selected temperature until the next program period begins. Then the thermostat will automatically revert to the program.

•HOLD TEMPERATURE — The thermostat can hold any temperature within its range for an indefinite period, without reverting to the programmed temperature. Press HOLD button. HOLD will be displayed. Then choose the desired

temperature by pressing or . The thermostat will hold the room temperature at the selected setting until you press the RUN button to start program operation again.

•ENERGY MANAGEMENT RECOVERY — Energy Manage- ment Recovery (EMR) causes the thermostat to start heating or cooling early to make the building temperature reach the

program setpoint at the time you specify. Heating will start 5 minutes early for every 1° of temperature required to reach setpoint.

Example: You select EMR and have your heating pro- grammed to 65° at night and 70° at 7 AM. If the building temperature is 65° the difference between 65° and 70° is 5°.

Allowing 5 minutes per degree the thermostat setpoint will change to 70° at 6:35 AM. Cooling allows more time per degree because it takes longer to reach temperature.

•°F/°C CONVERTIBILITY — The factory default setting is Fahrenheit. Clipping W904 jumper on the circuit board (see fig. 1) will alter this feature to Celsius temperature setting.

Configuration Menu

Step

Press Button(s)

Displayed (Factory Default)

Press

or

to select:

COMMENTS

 

 

 

 

 

 

 

1

PRGM

FA

 

OFF

 

Select Fast (on) or slow (off) Second Stage Heat

and RUN

(on)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

HOLD*

CL

 

ON

 

Select Compressor lockout OFF or ON

(OFF)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

HOLD*

0 HI

 

3 LO TO

 

Select temperature display adjustment higher or lower

(0)

 

3 HI

 

 

 

 

 

 

4

RUN

 

 

 

 

Returns to normal operation

 

 

 

 

 

 

 

* Press HOLD to advance to next item or TIME to move backwards to previous item

www.white-rodgers.com

Page 4 Page 6
Page 5
Image 5
White Rodgers 1F72 installation instructions Configuration Menu, Operating Features, From Fourth, Display
Page 4 Page 6

1F72 specifications

The White Rodgers 1F72 is a highly regarded thermostat known for its reliability and advanced features, designed primarily to enhance comfort and energy efficiency in residential heating and cooling systems. A product of White Rodgers, a reputable brand in HVAC controls, the 1F72 is engineered to integrate seamlessly with various HVAC systems while providing intuitive user control.

One of the standout features of the White Rodgers 1F72 is its programmable capabilities. This thermostat allows users to set different temperature schedules for various times of the day and days of the week. Users can easily program it to lower the temperature at night and raise it again in the morning, leading to significant energy savings without sacrificing comfort. The flexible scheduling feature makes it suitable for families with varying routines.

The user interface of the 1F72 is designed for ease of use. It features a large, easy-to-read display that provides clear temperature settings and options. The thermostat’s buttons are intuitive, allowing users to adjust settings with minimal effort. The simple design is especially beneficial for individuals who may not be technically inclined.

Another notable technology incorporated in the White Rodgers 1F72 is the Smart Recovery feature. This innovative capability enables the thermostat to start heating or cooling the home before the programmed time, ensuring that the desired temperature is reached just when it's needed. This proactive approach contributes to improved energy efficiency.

The 1F72 is compatible with a wide range of heating and cooling systems, including conventional systems, heat pumps, and multi-stage systems. This versatility makes it an excellent choice for different types of homes and setups.

In addition to its programmable functionality, the thermostat also features advanced temperature control capabilities. With the precision of its temperature sensor, the 1F72 ensures that the home's temperature remains as consistent as possible, enhancing comfort and reducing energy waste.

Overall, the White Rodgers 1F72 thermostat is an exemplary device for anyone looking to manage their home’s heating and cooling needs effectively. With its programmable schedules, user-friendly interface, and compatibility with various systems, it stands out as an optimal solution for modern HVAC control demands.
Top Page Image Contents