Vacuum Motor Replacement

Wire Terminal

ONLY QUALIFIED

! WARNING: MAINTENANCE

PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS.

1.	Turn off all switches and unplug machine.
2.	Remove recovery tank.
3.	Remove the (2) screws that fasten the
	solution tank to the frame, and tilt tank back
	to expose the inside of the frame.
4.	Locate the vacuum motor wires and
	disconnect at the connector. Close the
	solution tank.
5.	Remove the (6) screws holding the vacuum
	motor cover (p/n 86003080-PRV NO.
	27809) to the solution tank.

MAINTENANCE

Vac Motor Carbon Brushes Replacement (Ametek)

		End Cap
	Carbon Brushes	WARNING: The green
	Carbon Brushes	ground wire must be
		ground wire must be
		attached for safe
		operation.
		See wiring diagram.

Note: When replacing carbon vac motor brushes loosen wire terminal BEFORE removing screws on bracket.

If armature commutator is not concentric, extremely pitted, or grooved the motor will need to be replaced or sent to a qualified service center to restore vac performance.

6.	Remove the vacuum motor.
7.	Reverse process to install vacuum motor.

Vacuum Motor Carbon Brushes Replacement (Windsor)

	End Cap
Carbon	WARNING: The green
Brushes	ground wire must be
	attached for safe operation.
	See wiring diagram.

Important:

These brushes wear quicker as the length shortens due to increased heat.

Spring inside brush housing will damage motor if brushes are

allowed to wear away completely.

Wire

Terminal

Note: Place stop in groove.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

38 [9.5mm]

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

3/8

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" long.

CADET 86038340 04/19/07

4-2ENG

CDT7IB/10080060, CDT7IE/10080070, CDT7IA/10080050, CDT7IS/10080080 specifications

Windsor has established itself as a leader in the field of commercial cleaning equipment, with a particular focus on floor care. Among its notable offerings are the Windsor CDT7IE, CDT7IS, CDT7IA, and CDT7IB models. Each of these machines is designed to meet the varying needs of different cleaning environments, providing both versatility and efficiency.

The CDT7IE model stands out with its exceptional ergonomic design, which enhances user comfort during prolonged cleaning tasks. It features advanced filtration technology that captures dust and allergens, making it ideal for healthcare environments and facilities requiring stringent cleanliness standards. Its powerful suction capabilities ensure optimal dirt and debris removal, while adjustable height settings allow for seamless transitions between different floor surfaces.

On the other hand, the CDT7IS is engineered with enhanced durability in mind, making it perfectly suited for high-traffic areas. This model is built with reinforced components that withstand the rigors of daily use, ensuring longevity and reliability. Additionally, it comes with an easy-to-use control panel, which simplifies operation for users of all skill levels. The CDT7IS also boasts a large-capacity dust bag, reducing the frequency of changes and allowing for longer cleaning intervals.

The CDT7IA model emphasizes versatility, as it is designed for various applications, including both hard and soft floor surfaces. Its dual-mode feature allows users to switch between deep cleaning and maintenance modes, providing flexibility for different cleaning needs. This model also integrates eco-friendly technologies, including energy-efficient motors that reduce power consumption without compromising performance.

Lastly, the CDT7IB model is specifically tailored for industrial and commercial use, featuring a rugged design that can tackle tough cleaning challenges. Its robust brush system provides excellent agitation on carpets, lifting dirt and grime effectively. The CDT7IB is not only powerful but also easy to maneuver, thanks to its low profile and lightweight construction.

Overall, each of the Windsor CDT7 models brings a unique set of features and technologies to the table, catering to the diverse requirements of the modern cleaning industry. Their combination of innovative design, advanced technologies, and user-focused features makes them reliable choices for professional cleaning tasks. Whether for healthcare, commercial, or industrial use, Windsor’s CDT7 series continues to uphold the brand's commitment to quality and performance in floor care.

Windsor CDT7IA/10080050, CDT7IE/10080070 manual Vacuum Motor Replacement, Remove the vacuum motor

Models: CDT7IB/10080060 CDT7IE/10080070 CDT7IA/10080050 CDT7IS/10080080