MAINTENANCE

PERIODIC MAINTENANCE

Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them thoroughly, and blow-dry.

NOTE: Do not use pins, wire, etc. to clean nozzles as this could destroy spray pattern.

Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. If the cable insulation is broken or frayed, repair or replace it immediately. Don’t take chances with electrical fire or shock.

DAILY / REGULAR MAINTENANCE

Before making any adjustments or repairs to the machine, disconnect the power cord from electrical source.

1.Empty unused cleaning solution from the solution tank.

2.Inspect and clean filter screen in solution tank.

3.Flush pumping system with 4 or 7 liters of clean, hot water.

4.After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a 1-10 bleach to water solution. Waste water should be disposed of properly.

5.Check for and remove any lint or debris around vac shoe.

6.Check spray jets for full spray pattern.

7.Remove lint and dirt build-up from brush and housing.

NOTE: Brush removal.

A.To remove brush, grab and pull brush out from end opposite drive belt (operator’s right). Remove other end from brush driver.

B.To install brush, line up slots in brush core with pin in driver on drive belt side (operator’s left) and push brush onto driver. Then snap bearing end (opposite end) of brush into retaining clip.

8.Check cooling air screen (located on frame behind left wheel) for lint or debris.

9.Check float and shut-off screen and clean as necessary.

NOTE: Always store machine with brush in “Store” position.

4-1ENG

CADET 86038340 04/19/07

Page 17 Page 19
Page 18
Image 18
Windsor CDT7IS/10080080, CDT7IE/10080070, CDT7IB/10080060 manual Periodic Maintenance, Daily / Regular Maintenance
Page 17 Page 19

CDT7IB/10080060, CDT7IE/10080070, CDT7IA/10080050, CDT7IS/10080080 specifications

Windsor has established itself as a leader in the field of commercial cleaning equipment, with a particular focus on floor care. Among its notable offerings are the Windsor CDT7IE, CDT7IS, CDT7IA, and CDT7IB models. Each of these machines is designed to meet the varying needs of different cleaning environments, providing both versatility and efficiency.

The CDT7IE model stands out with its exceptional ergonomic design, which enhances user comfort during prolonged cleaning tasks. It features advanced filtration technology that captures dust and allergens, making it ideal for healthcare environments and facilities requiring stringent cleanliness standards. Its powerful suction capabilities ensure optimal dirt and debris removal, while adjustable height settings allow for seamless transitions between different floor surfaces.

On the other hand, the CDT7IS is engineered with enhanced durability in mind, making it perfectly suited for high-traffic areas. This model is built with reinforced components that withstand the rigors of daily use, ensuring longevity and reliability. Additionally, it comes with an easy-to-use control panel, which simplifies operation for users of all skill levels. The CDT7IS also boasts a large-capacity dust bag, reducing the frequency of changes and allowing for longer cleaning intervals.

The CDT7IA model emphasizes versatility, as it is designed for various applications, including both hard and soft floor surfaces. Its dual-mode feature allows users to switch between deep cleaning and maintenance modes, providing flexibility for different cleaning needs. This model also integrates eco-friendly technologies, including energy-efficient motors that reduce power consumption without compromising performance.

Lastly, the CDT7IB model is specifically tailored for industrial and commercial use, featuring a rugged design that can tackle tough cleaning challenges. Its robust brush system provides excellent agitation on carpets, lifting dirt and grime effectively. The CDT7IB is not only powerful but also easy to maneuver, thanks to its low profile and lightweight construction.

Overall, each of the Windsor CDT7 models brings a unique set of features and technologies to the table, catering to the diverse requirements of the modern cleaning industry. Their combination of innovative design, advanced technologies, and user-focused features makes them reliable choices for professional cleaning tasks. Whether for healthcare, commercial, or industrial use, Windsor’s CDT7 series continues to uphold the brand's commitment to quality and performance in floor care.
Top Page Image Contents