OPERATION

HEATER OPERATION

The disconnect fittings on the heater will become extremely

hot during operation. Allow sufficient time to cool, or run solution through the machine with the heater turned off before disconnecting the or performing any maintenance on the heater.

Before disconnecting the heater, open wand valve to relieve the system of all pressure by depressing the valve trigger.

DO NOT spray water directly on to the heater. To clean, unplug the unit and wipe with a damp cloth.

Make certain that the solution tank is filled adequately before

plugging in the machine and heater.

1.Plug the machine and heater into separate grounded circuits. The heater draws 15 amps of current.

2.Turn the solution pump ON. Turn the heater switch ON. The solution pump must be turned on BEFORE the heater is turned on.

The heater requires about 5-6 minutes to reach operating temperature, approximately 250°F. When turning the machine and heater OFF, make certain that you turn the heater off FIRST.

EMPTYING AND CLEANING

Always use defoamer if foaming occurs. Foam will

suspend large particles that may damage vacuum(s) as well as allow liquid into the vacuum motor(s) without activating the float shutoff.

1.Before proceeding, make certain that the nozzle is functioning properly.

a.To check, hold the wand about one foot above the surface to be cleaned and open the wand valve. A full spray should be observed from the nozzle.

b.If the nozzle is not showing a full spray pattern, adjust nozzle for proper pattern, clean, or replace nozzle.

2.Normally, chemical is applied on the push stroke

while vacuuming is done on the pull stroke. For heavily soiled carpets the hand tool may

be used in the scrubbing manner, applying chemical in both the push and pull stroke.

ALWAYS FINISH UP AN AREA WITH A VACUUM PULL STROKE.

3.When cleaning, keep the working opening (wand mouth) flat on the surface being cleaned. Keep the wand moving when the valve is open.

4.The shutoff float inside the recovery tank will impede the vacuum flow when the tank is full. When this occurs, empty the recovery tank. Do this by opening the dump valve located at the back of the machine. NOTE: Dispose of waste in a proper manner which would not violate any Local, State or Federal law.

5.Once the recovery tank has been emptied, you may once again proceed with cleaning.

Operating Vacuum after shutoff has activated could draw water

directly into the vac motor. This will cause damage to the motor, therefore voiding your warranty.

Always test carpet for color fastness in an inconspicuous

place. Also, to avoid prolonged drying times, do not spray too much solution in any one area.

SHUT DOWN AND STORAGE

1.Turn Switch OFF. Empty recovery tank

completely and rinse several times to remove

any dirt or debris that may be left behind.

2.Drain any unused cleaning solution from solution tank and rinse with clean water to remove any suds left behind by the cleaning chemicals. NOTE: Dispose of waste in a proper manner which would not violate any Local, State or Federal law

3.Run a small amount of clean water through pump if chemicals were used. This will help insure the life of your pump.

4.Check the spray jet on the cleaning tool for full spray pattern and inspect vac head for any obstructions.

5.Remove as much moisture from system before

storing in cold climates. Excess water may freeze during storage and crack internal components, causing damage to the unit.

Before making any adjustments or performing any

maintenance to your machine, disconnect the power cord from the electrical source.

5

D-250 98828 04/08/03

 

Page 6
Image 6
Windsor D250 (115V) manual Heater Operation, Emptying and Cleaning, Shut Down and Storage

D250 (115V) specifications

The Windsor D250 (115V) is a powerful and versatile floor scrubber designed to meet the cleaning needs of various commercial environments. Known for its durability and efficiency, the D250 is an excellent choice for facilities management in schools, warehouses, retail spaces, and healthcare settings.

One of the standout features of the Windsor D250 is its compact design. This makes it easy to maneuver in tight spaces and provides superior cleaning capabilities even in hard-to-reach areas. The unit is built with a high-performance motor that delivers consistent power, ensuring it can tackle heavy-duty cleaning tasks without compromising performance.

Equipped with a dual scrub deck, the D250 utilizes two counter-rotating brushes that improve dirt and stain removal. This technology allows for effective scrubbing without the hassle of frequent brush changes or complicated maintenance. The scrub deck can be easily adjusted depending on the surface type, allowing for versatility in cleaning applications from smooth floors to textured surfaces.

The D250 features a user-friendly control panel that simplifies operation. With intuitive controls, even staff with minimal training can quickly become proficient in using the machine. Additionally, the adjustable handle provides ergonomic benefits, reducing operator fatigue during prolonged use.

In terms of water management, the Windsor D250 incorporates an efficient solution distribution system. This ensures optimal water usage, minimizing waste while maximizing cleaning efficiency. The recovery tank design is also noteworthy; it features an easy-to-empty design that facilitates the swift removal of dirty water, accelerating the cleaning process.

The D250 is designed for durability with high-quality materials that enhance its lifespan. Furthermore, its low noise operation makes it suitable for use in noise-sensitive areas, allowing cleaning to take place without disrupting regular activities.

For maintenance, the Windsor D250 requires minimal intervention. With access to components such as brushes and filters easily available, routine maintenance becomes a straightforward task. This aspect of design not only saves time but also reduces operational costs.

Overall, the Windsor D250 (115V) is a commendable floor scrubber that combines innovative technology with user-friendly features. Its robust construction, effective cleaning capacity, and ease of use make it a reliable choice for any commercial cleaning environment. Whether for heavy-duty applications or routine maintenance, the D250 is engineered to get the job done efficiently while ensuring the highest standards of cleanliness.