Woods Equipment 872500G, 872502G, MZ2661K - page 6

6

WOODS

ASSEMBLY AND SETUP

TOOLS REQUIRED FOR ASSEMBLY

- Wrecking bar

- Claw hammer

- Ratchets: 3/8”,e

- Sockets: 9/16”, 3/4"

- Wrenches: 3/8", 9/16", 3/4"

- Straight edge

- Tire pressure gauge

- Blocks (for deck leveling)

NOTE: All references below to the “right” or “left” are with respect to an operator at the controls.

1. UNCRATE UNIT

Discard packing materials. Remove and discard shipping brackets. Tighten caster wheel axle bolts

against caster axle spanner bushings.

2. Set rear tire pressures to 12 lbs/in2 (1.0 kg/cm2). Tires are overinated for shipping. Front tires are run at

tires

3. DECK LEVELING

a) Park the machine on a smooth, level surface.

Raise the deck to the transport position.

b) Lower the deck onto a pair of equal height blocks

A under the rear corners of the deck. Place an-

other pair of adjustableblocks B under the front of

the deck so that the deck top is pitched forward

1/8”.

NOTE: The front and rear of the deck are at different

heights.

c) Measure the height of the blade cutting edge

above the ground. Remove pin C and set the

height of cut lever D to that height.

d) Loosen nuts I at all four corners of the deck.

NOTE: This will relieve tension on chains H.

e) Loosen the jam nuts E on the height of cut clips

F and adjusting screws G. Turn the adjusting

screws G until the play is taken out of the chains

H at all four corners. Tighten the jam nuts E

against the clips F and at the adjusting screws G.

Retighten nuts I at this time.

Contents

Main PARTS MANUAL MOWN MACHINE MAN0865 MZ2252K MZ2661K AVERTISSEMENT WARNING IMPORTANT MESSAGE TABLE OF CONTENTS WOODS NOTICE !!! ATTENTION! BECOME ALERT! Signal word denitions Page ASSEMBLY AND SETUP MAINTENANCE CHART ECNANETNIAM NOITAREPO E N I G N E SCILUARDYH ENIHCAM Page CHECK DAILY BATTERY Page HYDRAULIC SYSTEM WOODS SPARK PLUGS ENGINE OIL FUEL FILTER HEAVY DUTY CYCLONIC AIR CLEANER ENGINE COOLING WOODS CLEANING MACHINE WASHING MACHINE Page DECK LEVELING REAR DECK ROLLERS HEIGHT OF CUT COUNTERBALANCE SPRINGS WOODS PARKING BRAKE CONTROL LEVERS TRACKING HANDLES FRONT DECK LIP DAMPERS WOODS HYDROSTAT ADJUSTMENTS BELT REPLACEMENT CUTTERDECK BELT A PUMP-DRIVE BELT POWER UNITS ENGINES: DRIVE SYSTEM: OPERATOR PRESENCE INTERLOCK SYSTEM: WEIGHT: ENGINES WOODS LARENEG ENIGNE CONSTRUCTION: CUTTERDECK DRIVE SYSTEM: CUTTERDECKS Page FIGURE 1 UPPER ENGINE DECK ASSY FIGURE 1 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY * NOT ILLUSTRATED UPPER ENGINE DECK ASSY FIGURE 2 LOWER ENGINE DECK ASSY/CLUTCH FIGURE 2 LOWER ENGINE DECK ASSY/CLUTCH FIGURE 3 BUMPER FIGURE 3 FIGURE 4 FUEL TANKS/CONTROL PANEL FIGURE 4 FUEL TANKS/CONTROL PANEL FIGURE 5 BRAKES/REAR WHEEL FIGURE 5 BRAKES/REAR WHEEL FIGURE 6 OIL COOLER FIGURE 6 FIGURE 7 AIR COOLED HYDRAULICS FIGURE 7 AIR COOLED HYDRAULICS FIGURE 8 HYDROGEAR PUMP WOODS HYDROGEAR PUMP FIGURE 9 AIR COOLED WIRE HARNESS BATTERY ENGINE BLOCK (GROUND) (BLACK) (RED) AIR COOLED WIRE HARNESS FIGURE 9 Page SEAT ASSEMBL Y FIGURE 10 FIGURE 11 OPTIONAL FOLDING ROPS KIT (970410) FIGURE 11 OPTIONAL FOLDING ROPS KIT (970410) FIGURE 12 STEERING/DECK LIFT FIGURE 12 STEERING/DECK LIFT FIGURE 13 CRADLE ASSEMBLY FIGURE 13 CRADLE ASSEMBLY FIGURE 14 CRADLE & CASTER ASSEMBLY FIGURE 14 CRADLE & CASTER ASSEMBLY FIGURE 15 52" SIDE DISCHARGE FIGURE 15 52" SIDE DISCHARGE FIGURE 16 61" SIDE DISCHARGE FIGURE 16 61" SIDE DISCHARGE Page Page FIGURE19 DECALS-POWER UNIT FIGURE 19 Page Page Woods Equipment Company LIMITED WARRANTY (Mown MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) LIMITED WARRANTY (Mown MachineTM Zero-Turn Mower and Woods BoundaryTM Utility Vehicle Replacement Parts)