Manuals / Brands / Computer Equipment / Power Supply / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology RS232-HPD, RS232-XT Tabl e 1.2 Specifications for HPD 300 W Series Supply with RS-232 Interface Installed

1 62

Download 62 pages, 555.95 Kb

Features and Specifications

Specifications

14 Operating Manual for RS-232 for XT/HPD Series Power Supply

Tabl e 1.2 Specifications for HPD 300 W Series Supply with RS-232 Interface Installed

Models 15-20 30-10 60-5

Program Resolution

Voltage

Current

OVP

2.4mV

2.8mA

2.4mV

4.7mV

1.4mA

4.7mV

9.3mV

0.7mA

9.3mV

Program Accuracy1

Voltage

Current

OVP

1. Apply accuracy specifications according to the following voltage program accuracy example:

Set a model HPD 15-20 power supply to 10 volts.

The expected result will be within the range of 10volts ± 20mV ± 0.1% of the set voltage of

10 volts.

60mV

±0.1%

75mA

±0.12%

150mV

70mV

±0.1%

50mA

±0.12%

300mV

90mV

±0.12%

25mA

±0.1%

600mV

Readback Resolution

Voltage

Current

2.4mV

2.8mA

4.7mV

1.4mA

9.3mV

0.7mA

Readback Accuracy1

Voltage

Current

45mV

±0.3%

75mA

±0.12%

90mV

±0.3%

40mA

±0.12%

175mV

±0.3%

25mA

±0.1%

Contents

Main Page Page Limited Warranty Page Disclaimer Exclusions Page Page About This Manual Main Sections Manual Revisions Page Contents Section 1. Features and Specifications Section 2. Installation and Configuration Section 3. Operation Section 4. Calibration Section 1. Features and Specifications Description Page Specifications Table 1.1 Specifications for XT 60 W Series Supply with RS-232 Interface Installed Tabl e 1.2 Specifications for HPD 300 W Series Supply with RS-232 Interface Installed Section 2. Installation and Configuration Initial Inspection 16 Figure 2.1 Power Supply Front Panel with RS-232 Interface Installed Figure 2.2 Power Supply Rear Panel with RS-232 Interface Installed Page Initial Inspection Figure 2.3, RS-232 Interface PCB continued. 18 Basic Setup Procedure Page Communications Page Page Page Remote/Local Operation Page RS-232 Connection Power Supply Settings Table 2.12 Power Supply Settings User Options and Settings Page User Signals User Signals MCT6 32 Figure 2.6 J7 User Signal Connector Circuit Block Diagram J7 Cable Connection MCT6 Page Page Section 3. Operation Introduction RS-232 Operation Command Syntax Page Operation Command Syntax Table 3.1 Command Parameters Floating Point Number <float> Variables sent with command parameters are Table 3.2 Floating Point Numbers Parameter Description Form Floating Number Definition Example Page Command Summary Table 3.3 Programming Commands Table 3.4 Query Commands Table 3.5 Calibration Commands Table 3.6 Status Commands Command Reference Table 3.7 Command Reference 49 Page Command on page 25 Status, and Fault Registers on page 49 Accumulated Status, Status, and Fault Registers on page 49 Registers on page 49 Page Accumulated Status, Status, and Fault Registers Table 3.8 Accumulated Status, Status, and Fault Registers Notes: Error Codes Table 3.9 Error Codes Troubleshooting Section 4. Calibration Voltage Mode Calibration Page Current Mode Calibration Page Over Voltage Protection (OVP) Calibration Page Xantrex Technology Inc.