Manuals / Brands / Computer Equipment / Power Supply / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology RS232-HPD, RS232-XT Figure 2.3, RS-232 Interface PCB continued.

1 62

Download 62 pages, 555.95 Kb

Installation and Configuration

Initial Inspection

18 Operating Manual for RS-232 for XT/HPD Series Power Supply

Figure 2.3, RS-232 Interface PCB continued.

JUMPER SELECTION

J95 Local OVP control selection [closed] [default]. See page 29.

[open] See Table 2.13, on page 29.

J117 User TTL shutdown (S/D)

selection

[1-2] User TTL S/D line active low.

[2-3] [default] User TTL S/D line active high.

J217 Remote OVP Control Selection [closed] [default]. See page 29.

[open] See Table 2.13, on page 29.

J7 RS-232 (J5) transmit and

receive pin selection

[3-1] Transmit on pin 3 [default]

[4-6] Receive on pin 2 [default]

[3-5] Transmit on pin 2

[4-2] Receive on pin 3

J8 RS-232 flow control selection of

RTS/CTS (ready to send/clear

to send) or DTR/DSR (data

terminal ready/data set ready)

[2-4][3-5] [default] RTS input on pin 7 (used with

CTS output on pin 8)

[2-4][1-3] DTR input on pin 4 (used with DSR

output on pin 6)

J9 RS-232 flow control selection of

RTS/CTS or DTR/DSR

[1-3][4-6] [default] CTS output on pin 8 (used

with RTS input on pin 7)

[3-5][4-6] DSR output on pin 6 (used with DTR

input on pin 4)

Note: All other jumpers are not user-selectable.

LED INDICATORS

CR141 Red Diagnostic LED Bus error or soft restart on Slave circuitry.

CR14 Red Diagnostic LED Soft restart on Master circuitry.

CR13 Green Diagnostic LED Bus error on Master cir cuitry.

EPROMS

U95 Slave EPROM See revision number stamped on EPROM.

U18 Master EPROM See revision number stamped on EPROM.

Contents

Main Page Page Limited Warranty Page Disclaimer Exclusions Page Page About This Manual Main Sections Manual Revisions Page Contents Section 1. Features and Specifications Section 2. Installation and Configuration Section 3. Operation Section 4. Calibration Section 1. Features and Specifications Description Page Specifications Table 1.1 Specifications for XT 60 W Series Supply with RS-232 Interface Installed Tabl e 1.2 Specifications for HPD 300 W Series Supply with RS-232 Interface Installed Section 2. Installation and Configuration Initial Inspection 16 Figure 2.1 Power Supply Front Panel with RS-232 Interface Installed Figure 2.2 Power Supply Rear Panel with RS-232 Interface Installed Page Initial Inspection Figure 2.3, RS-232 Interface PCB continued. 18 Basic Setup Procedure Page Communications Page Page Page Remote/Local Operation Page RS-232 Connection Power Supply Settings Table 2.12 Power Supply Settings User Options and Settings Page User Signals User Signals MCT6 32 Figure 2.6 J7 User Signal Connector Circuit Block Diagram J7 Cable Connection MCT6 Page Page Section 3. Operation Introduction RS-232 Operation Command Syntax Page Operation Command Syntax Table 3.1 Command Parameters Floating Point Number <float> Variables sent with command parameters are Table 3.2 Floating Point Numbers Parameter Description Form Floating Number Definition Example Page Command Summary Table 3.3 Programming Commands Table 3.4 Query Commands Table 3.5 Calibration Commands Table 3.6 Status Commands Command Reference Table 3.7 Command Reference 49 Page Command on page 25 Status, and Fault Registers on page 49 Accumulated Status, Status, and Fault Registers on page 49 Registers on page 49 Page Accumulated Status, Status, and Fault Registers Table 3.8 Accumulated Status, Status, and Fault Registers Notes: Error Codes Table 3.9 Error Codes Troubleshooting Section 4. Calibration Voltage Mode Calibration Page Current Mode Calibration Page Over Voltage Protection (OVP) Calibration Page Xantrex Technology Inc.