Troubleshooting
Problem | Cause | Solution | See | |
page | ||||
|
|
| ||
The volume, subwoofer and | The adjustment has reached the maximum or |
| ||
audio delay time is not | minimum. |
|
| |
adjustable. |
|
|
| |
|
|
|
| |
The unit does not learn the | The remote control sensor of the unit may be | Reposition the unit. | — | |
operation of TV remote | exposed to direct sunlight or lighting. |
|
| |
control. |
|
|
| |
The screen glare of TV disturbs the remote | Disconnect the power cable and perform the | — | ||
| ||||
| control signal. | remote control learning operation again. |
| |
|
|
|
| |
| The batteries of TV remote control may be worn | Replace the batteries. | — | |
| out. |
|
| |
|
|
|
| |
| The button of the unit was not pressed long | Press the button of TV remote control in the | ||
| enough for the remote control learning | order “press 1 second” → “release 1 second” → |
| |
| operation. | “press 1 second” |
| |
|
|
|
| |
| The TV remote control is not available for | Use the remote control of the unit. | ||
| remote control learning. |
|
| |
|
|
|
| |
| The TV remote control is outside of the | Point your TV remote control towards the | ||
| operation range. | remote control sensor of the unit keeping a |
| |
|
| distance of 30 cm (1 ft) between them. |
| |
|
|
|
| |
| The unit does not enter the remote control | Operate after checking that the INPUT | ||
| learning mode. | indicator is flashing in red. |
| |
|
|
|
| |
The power state of the unit | The power state of the unit and of your TV is | Press the power button of TV remote control to | ||
and of your TV is opposite. | opposite from the beginning. | set your TV and the unit to standby mode after |
| |
(For example, though your |
| pressing the power button of your TV itself and |
| |
TV is on, the unit is in |
| of the unit to set both your TV and the unit to on. |
| |
standby mode.) |
|
|
| |
|
|
|
| |
The TV remote control is out | The unit and TV are too close/far from one | Try to use the TV remote control relay function | ||
of work even if you use TV | another. | again after repositioning the TV remote control |
| |
remote control relay |
| signal transmitter of the unit and the remote |
| |
function. |
| control sensor of your TV. |
| |
|
|
|
| |
|
| Try to use the TV remote control relay function | ||
|
| again after adjusting the height of the unit by |
| |
|
| removing or attaching its stands. |
| |
|
|
|
| |
| Something is between the unit and your TV. | Remove the obstruction. | — | |
|
|
|
| |
| The TV remote control relay function is not | Restart the unit and check the indicator status. | ||
| activated. |
|
| |
|
|
|
| |
| The TV remote control is not compatible with | Place the unit (without the stands, for example) | ||
| the TV remote control relay function. | so as not to hide the remote control sensor of |
| |
|
| your TV. |
| |
|
|
|
| |
You cannot use 3D glasses. | The unit obstructs the 3D glasses transmitter of | Check the position of 3D glasses transmitter of | — | |
| your TV. | your TV by referring to the manual of your TV, |
| |
|
| and move the unit to the position where there is |
| |
|
| no obstruction. |
| |
|
|
|
| |
The picture on your TV | The unit is too close to your CRT TV. | Move the unit away from your TV. | — | |
screen becomes blurred or |
|
|
| |
distorted. |
|
|
| |
|
|
|
|
Contact your nearest authorized Yamaha dealer or service center if the following problem occurs.
English
ProblemCauseSolution
See
page
The power of the unit | The protection circuit is activated. | — |
immediately shuts off, and |
|
|
the INPUT indicator flashes. |
|
|