mRear panel parts
GND terminal (For turntable use) *1Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected.
PRE OUT/MAIN IN terminals*2Removing the jumper pins from the PRE OUT/MAIN IN terminals enables this unit to operate separately as a control amplifier and a power amplifier. These terminals are used for connecting a
If such an external unit is connected to these terminals, the VOLUME control of this unit can be used for adjusting the overall sound level.
To connect an external unit, first remove the jumper pins from the PRE OUT/MAIN IN terminals, and then connect the input terminals of that unit to the PRE OUT terminals and its output terminals to the MAIN IN terminals. For details, refer to the owner’s manual included with the unit to be connected.
GND | AUDIO | SIGNAL |
| ||
|
| |
| R | |
| 2 | TUNER | L |
| COUPLER |
PHONO |
|
|
| ||
|
|
|
| R | |
R | 3 |
|
| PRE | L |
L | IN |
| OUT |
| |
|
| (PLAY) |
|
|
|
| 4 | TAPE |
| MAIN | R |
| OUT |
| IN |
| |
|
| (REC) |
|
|
|
3IN
1(PLAY)
CD/DVD MD
R
L | 4 | OUT | R |
|
| (REC) | |
|
| L | |
|
|
| |
|
| AUX |
|
|
|
| B |
Notes
cWhen you do not use the PRE OUT/MAIN IN terminals, never remove the jumper pins from these terminals. If removed, no sound will be outputted from this unit.
cWhen you use this unit with an external unit connected to the PRE OUT and MAIN IN terminals, make sure that the CD/DVD DIRECT AMP switch and the PURE DIRECT switch on the front panel are turned off.
cWhen you use this unit as a power amplifier, connect the output terminals of an external control amplifier etc. to this unit’s MAIN IN terminals. In this case, this unit’s controls will not function except the PHONES jack and the SPEAKERS switches. Use the controls on the
external control amplifier to make volume adjustment etc.
English
IMPEDANCE SELECTOR switch*3WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.
If this unit fails to turn on when the POWER switch is pressed:
The IMPEDANCE SELECTOR switch may not be set to either end. If so, set the switch to either end when this unit’s power supply is completely cut off.
Select the position whose | IMPEDANCE SELECTOR |
| |||||||||
| |||||||||||
requirements your speaker |
| SET BEFORE POWER ON |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
| |
system meets. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| A OR B : 4ΩMIN. /SPEAKER |
| A OR B : 6ΩMIN. /SPEAKER |
| |||||||
| A B : 8ΩMIN. /SPEAKER |
|
| A B : I2ΩMIN. /SPEAKER |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(Left position)
If you use one pair of speakers, the impedance of each speaker must be 4Ω or higher.
If you use two pairs of speakers, the impedance of each speaker must be 8Ω or higher.
(Right position)
If you use one pair of speakers, the impedance of each speaker must be 6Ω or higher.
If you use two pairs of speakers, the impedance of each speaker must be 12Ω or higher.
AC OUTLET(S) (SWITCHED)*4(U.S.A., Canada, Europe, China and General models)
...................................................... | 3 SWITCHED OUTLETS |
(U.K. and Australia models) ............. | 1 SWITCHED OUTLET |
Use these to connect the power cords of your components to this unit.
The power to the SWITCHED outlets is controlled by this unit’s POWER or STANDBY/ON switch. These outlets will supply power to any connected unit whenever this unit is turned on.
The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLET(S) is 100W.