20

Reference

Using the SHIFT-Related Functions
The enormous flexibility and power of the CBX-K2 is in its
“hidden” or SHIFT-related functions — allowing you to
send virtually any kind of MIDI message directly from the
keyboard or use the Assignable Wheel/Slider for real-time
control change.
In the instructions that follow, “L” refers to either of
the ENTER keys, J or K. In other
words, this means that either key can be used, unless
indicated otherwise.
NOTE
Both N / M
lamps flash briefly when a function is executed. The
LED display flashes briefly when a MIDI message is
sent.
The MIDI functions can be generally divided into three
types, according to their operation.
1) Holding C and pressing the function’s key. For
these functions, such as Sequencer Stop and Start,
pressing L is not necessary. These functions are
shown on the panel without underline.
2) Holding C, pressing the function’s key and then
L. These functions are indicated with a dashed
underline on the panel (for example, GM ON and XG
ON) and require pressing L to execute.
3) Holding C, pressing the function’s key, entering
a value and then pressing L. These functions
are indicated with an underline on the panel (for ex-
ample, PROGRAM CHANGE and TEMPO), and
require that a value (Decimal or Hexadecimal) be
entered.
When changing a function, the LED display indicates
the on/off status or the value of the function.
Many of the functions can be done with one or two key-
strokes, while others require you to enter a number value
and press one of the L keys to execute the function.
All functions can be accessed or executed by using one of
the operations described below.
In using the SHIFT-related functions, remember
Keep holding down C until the end of the
operation. If C is released in mid-operation,
you’ll have to start the operation all over again.
SEQUENCER PROGRAM SYSTEM WHEEL ASSIGN
STOP
SONG
SELECT
START TEMPOCONTINUE
BMEASURETOP BOTTOM
TIME SIGNATURE
FIXED
VELOCITY
MIDI
CH
MERGE
ON/OFF
SOUND
OFF XG
ON
GM
ON
VOICE
MAP POLY/
MONO
BANK
SELECT
PROGRAM
CHANGE
CHANNEL
MERGE
RESET
CONTROL
TG300B
RESET
SOUND OFF
ALL CH DEVICE
NUMBERTOUCH
SENSITIVITY
RPN NRPN DRUM
NUMBER
CONTROLLER
RPN NRPN DATA
DENSITY
MSB 1ST/
LSB 1ST
FOOT SW
ASSIGN
CONTROLLER
SLIDER ASSIGN
RPN NRPN DRUM
NUMBER
CONTROLLER
DATA
DENSITY
PB
DENSITY
RESET TRANSPOSE
1MODULATION
2BREATH
5PORTA TIME
6DATA ENTRY
7VOLUME
10PANPOT
11EXPRESSION
64HOLD1(DAMPER)
65PORTAMENTO
71HARMONIC
72RELEASE TIME
73ATTACK TIME
74BRIGHTNESS
84PORTA CTRL
123VIBRATO RATE
124VIBRATO DEPTH
125VIBRATO DELAY
126LP FILTER CUTOFF
127LP FILTER RESONANCE
128HP FILTER CUTOFF
129EQ LO GAIN
130EQ HI GAIN
131EQ LO FREQUENCY
132EQ HI FREQUENCY
133EG ATTACK TIME
134EG DECAY TIME
135EG RELEASE TIME
136DRUM LP FILTER CUTOFF
137DRUM LP FILTER RESONANCE
138DRUM EG ATTACK RATE
139DRUM EG DECAY RATE
140DRUM PITCH COARSE
141DRUM PITCH FINE
142DRUM LEVEL
143DRUM PAN
144DRUM REVERB
145DRUM CHORUS
146DRUM VARIATION
147DRUM HP FILTER CUTOFF
148DRUM EQ LO GAIN
149DRUM EQ HI GAIN
150DRUM EQ LO FREQUENCY
151DRUM EQ HI FREQUENCY
91REVERB
93CHORUS
94VARIATION
120PB SENSITIVITY
121FINE TUNE
122COARSE TUNE
CONTROLLER
NUMBER LIST CONTROL CHANGE
ENTER
HEXA
DECIMAL
DECIMAL
123456789ABCDEF0
B
RPN
NRPN 152CH PRESSURE
153KEY PRESSURE
154MASTER VOLUME
156MASTER TUNING
157VELOCITY
158TEMPO
OTHERS
L
keys
MIDI functions
(Group A and Group B) Value entry
(Decimal and Hexadecimal)
Displays current setting or value.
Display
ç key

Reference