Yamaha CP5, CP50 Settings for All Parts

Internal Design of the CP5 & CP50

Reference

Left & Right Parts

[VOICE]

[PRE-AMP]

[MOD-FX]

[PWR-AMP] (CP5 only)

[LEFT1]/[LEFT2]/[RIGHT1]/

[RIGHT2] (CP5)

[LEFT]/[RIGHT] (CP50)

[COMMON]

Song Setting Area

[SONG SETTING]

[RECORD]

TRACK Part

[TRACK]

MIC INPUT Part

[MIC INPUT] (CP5 only)

Settings for All Parts

[REVERB]

Settings for All Performances

[MASTER COMPRESSOR]

[UTILITY]

[FILE]

Appendix

42 CP5/CP50 Reference Manual

Settings for All Parts

Reverb Blo ck

This section describes the parameters used to configure the reverb effect that is applied to all of the

parts from each of your stage piano’s Performances. Settings for these parameters are made via

the Reverb screen, which contains two pages.

Edit Sequence Press and hold the [REVERB] button (for at least one second)  Navigate to the

required page using the [ PAGE] and [PAGE ] buttons  Turn Knobs 1 to 3

Page On-screen name

(and full name) Description

1RevType

(Reverb Type)

This parameter is used to select the type of reverb to be applied.

Setting values: RichHall, RichPlt, RichRoom, WoodRoom, Room1, Room2,

Stage1, or Stage2

RichHall (Rich Hall) Emulation of hall acoustics with a rich, deep reverb sound.

RichPlt (Rich Plate) Emulation of a rich, sustained plate reverb sound.

RichRoom

(Rich Room)

Emulation of room acoustics with a gentle reverb sound.

WoodRoom

(Woody Room)

Emulation of room acoustics with a warm reverb sound.

Room1 Emulation of room acoustics with a crisp reverb sound.

Room2 Emulation of room acoustics with a deeper reverb sound.

Stage1 Emulation of stage acoustics with a wide, sustained reverb

sound.

Stage2 Emulation of the reverb typical of a smaller stage.

2RevTime

(Reverb Time)

This parameter is used to set how long it takes in seconds for the reverb sound to

fade to silence.

Setting values: WoodRoom......................0.3s to 10.0s

Other reverb types...........0.3s to 30.0s

HPF (High-pass

Filter Cutoff)

This parameter is used to set the cutoff frequency for the Reverb block's high-pass

filter.

Setting values: 20Hz to 8.0kHz

FBHiDamp

(Feedback High

Damping)

This parameter is used to adjust the brightness’ of the reverb sound. At higher set-

tings, it takes longer for the high-frequency component to decay, producing a

brighter overall reverb sound. This parameter is not displayed on-screen when

RevType has been set to “WoodRoom”.

Setting values: 0.1 to 1.0

Contents

Main Reference Manual Contents Internal Design of the CP5 & CP50 3 Reference 12 Appendix 54 Reference Guides Owners Manual (hardcopy booklet) Reference Manual (this pdf document) Data List (pdf document) Using this Reference Manual Internal Design of the CP5 & CP50 Principal Components CP5/CP50 Tone Generator CP5 Parts CP50 Parts Performance Left & Right Parts Layered parts Split parts Parts Roles of Blocks & Common Settings Area Voi ce Bl ock Pre-Amplifier Block Modulation Effect Block Power-Amplifier / Compressor Block (CP5 only) TRACK Part MIC INPUT Part (CP5 only) Reverb Block Makeup of Performance Memories Preset Performance Memory External Performance Memory Preset Performance Memory User Performance Memory External Performance Memory 9 CP5/CP50 Reference Manual HINT Using External Performance Memories Song Setting Area Recording MIDI & Audio Data Playing MIDI & Audio Data Controller 12 CP5/CP50 Reference Manual Reference This section provides a detailed description of the parameters used to configure your CP5 or CP50. Left & Right Parts Voice Block The Voice block is used to set a basic sound for the currently selected part. Pre-Amplifier Block Configuring Pre-Amplifier Block Parameters On-screen name (and full name) Associated voices Description NOTE Voic e na me Description NOTE NOTE On-screen name (and full name) Associated voices Description 15 CP5/CP50 Reference Manual Modulation Effect Block For PIANO and E.PIANO voices: Selecting Modulation Effect Block Types On-screen name Selected modulation effect 16 CP5/CP50 Reference Manual Effect category Effect name On-screen name Effect category: Delay (DLY) Effect category: Chorus (CHO) Effect category: Distortion (DST) Effect category: Compressor (CMP) Effect category: Lo-fi (L-F) Effect category: Tech (TEC) Effect category: Misc (MSC) Configuring Modulation Effect Block Parameters NOTE On-screen name (and full name) Associated effects Description Effect category Effect name Parameters for Other effects On-screen name On-screen name (and full name) Associated effects Description Page Page Page Page Page Power-Amplifier / Compressor Block (CP5 only) Selecting Power-Amplifier / Compressor Block Types For PIANO and E.PIANO voices: For non-piano voices: Configuring Power-Amplifier / Compressor Block Parameters Power-Amplifier & Compressor Parameters 27 CP5/CP50 Reference Manual Other Settings for Left & Right Page NOTE Page On-screen name NOTE Page On-screen name 31 CP5/CP50 Reference Manual Common Settings Area Setting Performance Names & Playing Modes (Pages 1 and 2) Page On-screen name Description 32 CP5/CP50 Reference Manual Zone Edit Screen CP50 zones: (and full name) Description 34 CP5/CP50 Reference Manual Setting Controllers (Pages 3 to 5) Page On-screen name (and full name) Description CP50: NOTE CP50: Song Setting Area Song Setting Screen NOTE CAUTION (and full name) Description 37 CP5/CP50 Reference Manual Record Screen (and full name) Description Name screen NOTE NOTE (and full name) Description 39 CP5/CP50 Reference Manual TRACK Part (and full name) Description 40 CP5/CP50 Reference Manual MIC INPUT Part (CP5 only) Edit Sequence Mic Effects Screen Page On-screen name (and full name) Description Page On-screen name Mic Insert Effect Screen Edit Sequence 42 CP5/CP50 Reference Manual Settings for All Parts Reverb Blo ck 43 CP5/CP50 Reference Manual Settings for All Performances Master Compressor Block 44 CP5/CP50 Reference Manual Utility Area Page On-screen name (and full name) Description NOTE Page On-screen name (and full name) Description Page NOTE Page On-screen name (and full name) Description EQ Low EQ High NOTE Page On-screen name (and full name) Description 49 CP5/CP50 Reference Manual File Area Internal Design of the CP5 & CP50 50 CP5/CP50 Reference Manual Save The parameters to be set on the Save screen are as follows. If Typ e has been set to All: If Typ e has been set to Ext: On-screen name (and full name) Load On-screen name NOTE (and full name) Description On-screen name (and full name) Description If Typ e has been set to Perf: On-screen name On-screen name (and full name) Description 53 CP5/CP50 Reference Manual If Typ e has been set to SMF: Rename The parameters to be set on the Rename screen are as follows. Delete On-screen name On-screen name (and full name) Description Appendix MIDI MIDI Channels Supported MIDI Message Types Channel Messages Page Channel Mode Messages System Messages