Manuals / Yamaha / Home Audio / Stereo Receiver

Yamaha HTR-5560 owner manual Connecting the antennas, Connecting the AM loop antenna, Models

Models: HTR-5560

1 67

Download 67 pages 52.26 Kb

Page 21

CONNECTIONS

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

AM loop antenna

(included)Indoor FM antenna

(included)

EO

VIDEO

■Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it.

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and GND terminals.

PREPARATION

VIDEO

R OUT

TUNER
AM
ANT
GND
		DVD
75	UNBAL.	D-TV
FM		/CBL
FM
ANT
		MONIT
		OUT
FREQUENCY
	STEP

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

3 Orient the AM loop antenna for the best reception.

75-ohm/300-ohm antenna adapter (U.K. model)

1	2
	11	(7/16)
	8	(5/16)	Unit:
	6	(1/14)	mm (inch)
Open the cover of the	Cut the external sleeve
included 75-ohm/300-ohm	of the 75-ohm coaxial
antenna adapter.	cable and prepare it for
	connection.

3

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

FREQUENCY STEP switch (China and General

Lead wire

Cut the lead wire and remove it.

models)

FM/AM

50kHz/9kHz

100kHz/10kHz

FREQUENCY

STEP

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area.

4

Clamp	Clamp with
with	pliers.
pliers.
	Insert the wire
	into the slot.

Insert the cable wire into the slot, and clamp it with pliers.

5

Snap the cover into place.

North, Central and South America:

100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

17

Image 21

Yamaha HTR-5560 Connecting the antennas, Connecting the AM loop antenna, Frequency Step switch China and General, Models

Contents

HTR-5560 Explanation of Graphical Symbols Safety InstructionsExample of Antenna Grounding FCC Information for US customers onlyWe Want You Listening For a Lifetime Serial NoFor Canadian Customers Contents About this manual FeaturesChecking the package contents Getting StartedControl Front panel Controls and FunctionsSTEREO/EFFECT Remote control Handling the remote control Using the remote controlSelects the SET Menu mode STEREO/EFFECTFront panel display Speaker Setup Speaker placementSpeakers Connecting the speakers Subwoofer jack Diagram shows the speaker layout in the listening roomImpedance Selector switch Impedance Selector switchConnections Connecting to digital jacksConnecting video components Cable TV Video monitorGame console or Camcorder Connecting audio components Connecting a CD playerConnecting a CD recorder or MD recorder Connecting the AM loop antenna Connecting the antennasFrequency Step switch China and General ModelsConnecting an external decoder Turning on the power Connecting the power supply CordsConnecting the AC power cord Voltage Selector China and General modelsNrm Normal/-10 dB Speaker Mode SettingsAdjusting Speaker Output Levels Using the test toneBefore you begin Effect speakers using j So that it matches Adjust the levelWhen adjustment is Level of the main SpeakersBasic Playback To select the audio source connected to the 6CH Input jacksSelected input source When you have finished using this unit BGV background video functionTo mute the sound Input modes and indications Program name Program l / hSub-program name Program name Sub-program namePress q/DTS SUR Selecting PRO LogicEX or DTS ES software Playing Dolby Digital SurroundVirtual Cinema DSP Normal stereo reproductionUnderstanding sound fields Digital Sound Field Processing DSPHi-Fi DSP programs Recreating a sound fieldSound design of CINEMA-DSP CINEMA-DSPDolby Digital EX/DTS-ES compatible + DSP sound field effect Dolby Digital/DTS + DSP sound field effectDolby Pro Logic + DSP sound field effect Dolby Pro LogicCINEMA-DSP programs For movie programs No toTable of Program Names for Each Input Format Sci-Fi For audio-video sources No toAutomatic and manual tuning TuningAutomatic tuning Manual tuningAutomatically presetting stations for FM stations Presetting stationsTune in to a station Manually presetting stationsPress Memory MAN’L/AUTO FM Repeat steps 1 to 5 to store other stationsExchanging preset stations Tuning in to a preset stationPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit againSetting the sleep timer Sleep TimerCanceling the sleep timer To set the amount of timeSpecial considerations when recording DTS software Timer playback/recordingRecording SET Menu Adjusting the items on the SET1A Center center speaker mode Speaker SET speaker mode settingsLRG SML1C Rear LR rear speaker mode 1B Main main speaker mode1D Rear CT rear center speaker mode 1E Bass LFE/bass out mode1F Main Lv main level mode SP DLY Time speaker delay timeNrm 10 dBR Balance balance Main left and right speakers Range dynamic range10 MEM. Guard memory guard Input Mode initial input modeAuto LastControl area Remote Control FeaturesControlling this unit Controlling other componentSetting the manufacturer code Clearing setup manufacturer CodesClearing setup manufacturer code for the component control VCR Controlling other componentsPress j / i to adjust the speaker output level Adjusting the Level of the Effect SpeakersFor 6ch Stereo Subwoofer output levelPress j / i to adjust the delay time Adjusting the Delay TimeChanging parameter settings PRO Logic Music parameter DescriptionsCT Width Center width General TroubleshootingOnly the speaker on Sound suddenlyOne side can be HeardCheck SP Wires appears on the front panel display Other settings on this Unit cannot be ChangedNo sound from the rear center speaker Humming soundTuner Remote controlDolby Surround GlossaryDolby Digital DTS Digital Theater Systems Digital SurroundComponent video signal Video signalPCM Linear PCM Sampling frequency and number of quantized bitsSpecifications List of Manufacturer Codes Satellite Tuner Cable TVDBS VCRDVD Player CD PlayerCD RECORDER/CD LD PlayerTape Deck V874870