Troubleshooting, General | Yamaha HTR-5560 instruction

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.

■General

Problem	Cause	Remedy	Refer
			to page

This unit fails to turn	The power cord is not connected or the	Firmly connect the power cord.	—
on when STANDBY/	plug is not completely inserted.
ON (or SYSTEM
ON (or SYSTEM
POWER) is pressed,	The IMPEDANCE SELECTOR switch	Set the switch fully to the left or right position when	12
or enters in the	on the rear panel is not fully set to either	this unit is in the standby mode.
standby mode soon	the left or right position.
after the power has
after the power has
been turned on.	The protection circuitry has been	Make sure all speaker wire connections on this unit	10, 11
	activated.	and on all speakers are secure and that the wire for
		each connection does not touch anything other than
		its respective connection.

	This unit has been exposed to a strong	Set this unit in the standby mode, disconnect the	—
	external electric shock (such as lightning	power cord, plug it back in after 30 seconds, then
	and strong static electricity).	start operating.

No sound.	Incorrect input or output cable	Connect the cables properly. If the problem persists,	10 – 16
	connections.	the cables may be defective.

	An appropriate input source has not been	Select an appropriate input source with INPUT	23
	selected.	l/ h or 6CH INPUT (or the input selector buttons).

	The speaker connections are not secure.	Secure the connections.	10, 11

	The main speakers to be used have not	Select the main speakers with SPEAKERS A and/or	23
	been selected properly.	B.

	The volume is turned down.	Turn up the volume.	24

	The sound is muted.	Press MUTE or any operation buttons of this unit to	—
		cancel a mute and adjust the volume.

	Digital signals which this unit cannot	Play a source whose signals this unit can reproduce.	—
	reproduce are being input to this unit by
	playing a CD-ROM, etc.

The picture does not	The output and input for the picture are	Make connections using the same type of video	14, 15
appear.	connected to different types of video	jacks (S VIDEO, VIDEO (composite), or
	jacks.	COMPONENT VIDEO) for both the input and
		output.

52

Image 56

Yamaha HTR-5560 owner manual Troubleshooting, General

Contents

HTR-5560 Safety Instructions Explanation of Graphical Symbols FCC Information for US customers only Example of Antenna Grounding For Canadian Customers We Want You Listening For a LifetimeSerial No Contents Features About this manual Control Checking the package contentsGetting Started Controls and Functions Front panel STEREO/EFFECT Remote control Using the remote control Handling the remote controlSelects the SET Menu mode STEREO/EFFECT Front panel display Speakers Speaker SetupSpeaker placement Connecting the speakers Diagram shows the speaker layout in the listening room Subwoofer jack Impedance Selector switch Impedance Selector switch Connecting to digital jacks Connections Connecting video components Game console or Camcorder Cable TVVideo monitor Connecting a CD recorder or MD recorder Connecting audio componentsConnecting a CD player Connecting the antennas Connecting the AM loop antennaFrequency Step switch China and General Models Connecting an external decoder Connecting the power supply Cords Turning on the powerConnecting the AC power cord Voltage Selector China and General models Speaker Mode Settings Nrm Normal/-10 dB Before you begin Adjusting Speaker Output LevelsUsing the test tone Adjust the level Effect speakers using j So that it matchesWhen adjustment is Level of the main Speakers Selected input source Basic PlaybackTo select the audio source connected to the 6CH Input jacks To mute the sound When you have finished using this unitBGV background video function Input modes and indications Program l / h Program nameSub-program name Program name Sub-program name Selecting PRO Logic Press q/DTS SUR Playing Dolby Digital Surround EX or DTS ES softwareVirtual Cinema DSP Normal stereo reproduction Digital Sound Field Processing DSP Understanding sound fieldsHi-Fi DSP programs Recreating a sound field CINEMA-DSP Sound design of CINEMA-DSP Dolby Digital/DTS + DSP sound field effect Dolby Digital EX/DTS-ES compatible + DSP sound field effectDolby Pro Logic + DSP sound field effect Dolby Pro Logic Table of Program Names for Each Input Format CINEMA-DSP programsFor movie programs No to For audio-video sources No to Sci-Fi Tuning Automatic and manual tuningAutomatic tuning Manual tuning Presetting stations Automatically presetting stations for FM stations Manually presetting stations Tune in to a stationPress Memory MAN’L/AUTO FM Repeat steps 1 to 5 to store other stations Tuning in to a preset station Exchanging preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit again Sleep Timer Setting the sleep timerCanceling the sleep timer To set the amount of time Recording Special considerations when recording DTS softwareTimer playback/recording Adjusting the items on the SET SET Menu Speaker SET speaker mode settings 1A Center center speaker modeLRG SML 1B Main main speaker mode 1C Rear LR rear speaker mode1D Rear CT rear center speaker mode 1E Bass LFE/bass out mode SP DLY Time speaker delay time 1F Main Lv main level modeNrm 10 dB Range dynamic range R Balance balance Main left and right speakers Input Mode initial input mode 10 MEM. Guard memory guardAuto Last Remote Control Features Control areaControlling this unit Controlling other component Clearing setup manufacturer code for the component control Setting the manufacturer codeClearing setup manufacturer Codes Controlling other components VCR Adjusting the Level of the Effect Speakers Press j / i to adjust the speaker output levelFor 6ch Stereo Subwoofer output level Adjusting the Delay Time Press j / i to adjust the delay time CT Width Center width Changing parameter settingsPRO Logic Music parameter Descriptions Troubleshooting General Sound suddenly Only the speaker onOne side can be Heard Other settings on this Unit cannot be Changed Check SP Wires appears on the front panel displayNo sound from the rear center speaker Humming sound Remote control Tuner Glossary Dolby SurroundDolby Digital DTS Digital Theater Systems Digital Surround Video signal Component video signalPCM Linear PCM Sampling frequency and number of quantized bits Specifications List of Manufacturer Codes Cable TV Satellite TunerDBS VCR CD Player DVD PlayerCD RECORDER/CD LD Player Tape Deck V874870