Yamaha MD 8 14

14 Touring the MD8

MD8—Owner’s Manual

GINSERT I/O

These TRS phone jacks are used to connect signal processors for use with input channel 1

and input channel 2 exclusively. Typically, compressors, limiters, and noise gates are con-

nected to this type of connection.

HMIC/LINE INPUTs 1 & 2

These inputs are used to connect balanced condenser microphones and balanced line-level

signal sources to the MD8 (unbalanced sources can also be connected). Each input features

a XLR-type connector and TRS phone jack connector. Phantom power is available on the

XLR-type connector for use with condenser microphones. If you’re not using condenser

microphones with these inputs, keep the PHANTOM POWER ON/OFF switch set to OFF.

IMONITOR OUT

These phono jacks are used to send the monitor signals to a ste-

reo monitor ampliﬁer and speakers. This could be a dedicated

monitor ampliﬁer and speakers or your hi-ﬁ system. Connect

them to the monitor ampliﬁer’s stereo inputs. The MONITOR

OUT signal is the same as the headphone signal.

JSTEREO OUT

These phono jacks are used to connect a stereo master recorder

for recording the ﬁnal mix. The master recorder could be a DAT

deck, MiniDisc deck, or cassette tape deck. Connect them to your

master recorder’s stereo inputs.

K2TR IN

These phono jacks are used to connect the outputs of a stereo

master recorder to the MD8. The master recorder could be a DAT

deck, MiniDisc deck, or cassette tape deck. Connect them to your

master recorder’s stereo outputs. To monitor the output of the

stereo master recorder during mixdown, press the 2TR IN

MONITOR SELECT switch.

LTRACK DIRECT OUTs

These phono jacks are used to send the track signals to another

mixer. This is useful when you use the MD8 in conjunction with

a larger mixer. Connect them to the line inputs on the other

mixer. With no disc loaded, the DIRECT OUTs 1–4 output the

signals of Groups 1–4.

1/4" phone plug

1/4" phone plug

1/4" TRS phone plug To processor's input

From processor's output

Connect to INSERT I/O jack

Tip (send)

Tip (send)

Ring (return)

Sleeve (ground)

Sleeve (ground)

Tip (return)

Sleeve (ground)

Male XLR plug 1 (ground)

3 (cold)

2 (hot)

1/4" TRS phone plug

Tip (hot)

Ring (cold)

Sleeve (ground)

Phono plug Tip

Sleeve

Phono plug Tip

Sleeve

Phono plug Tip

Sleeve

Phono plug Tip

Sleeve

Contents

Main MULTITRACK MD RECORDER Owners Manual IN OUT 1 2 3 IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord Explanation of Graphical Symbols SAFETY INSTRUCTIONS CAUTION ii Important Cautions Warnings Read the Following Before Operating the MD8 Keep This Manual For Future Reference iv Contents 1. Welcome to the MD8 . . . . . . . . . . . . . . . . 1 4. Recording & Mixing Techniques . . . . . . . 26 3. The First Session . . . . . . . . . . . . . . . . . . . 16 2. Touring the MD8 . . . . . . . . . . . . . . . . . . . . 4 5. Quick Search Functions . . . . . . . . . . . . . . 51 8. Other Functions . . . . . . . . . . . . . . . . . . . 72 7. Editing Songs & Tracks . . . . . . . . . . . . . . 61 6. Repeat, Cue List & Program Play . . . . . . 57 Page 1 Welcome to the MD8 Recorder Mixer MD8 Features Page Buying Discs for the MD8 MD8 TOC Touring the MD8 Touring the MD8 IN OUT 1 2 3 Input Channels AUX controls E EQ controls F H G Master Section 910/1112 input level controls A MD8 Song K NMLJ Display REC S 1 2 3 4 5 6 7 8 9 10E IN OUT F G H I J Disc Transport Section E F G H I Rear Panel A B C 1 2 3 D 9 E J K L M F 14 G H I J Front Connectors A B 1 2 16 3 Quick-Start System Connecting the Power Cord Turning on the MD8 Loading a Disc Recording the First Track 18 Making the Connections (GRP & DIR) GRP Method DIR Method Monitoring & Recording (GRP & DIR) Listening to the First Track 20 Overdubbing Mixdown 22 An Overview of Multitrack Recording Basic Multitracking Advanced Multitracking About Monitoring 24 Multi-Source Mixing Track 1 (disc) Input 1 (jack/XLR) Track 1 (disc) 3. Set the PAN and CUE PAN controls on each input channel to their center positions. Page 26 4 Recording a New Song Blank 1 Searching for Blanks Setting the Recording Mode 28 Recording Titling Discs & Songs Manual Punch In/Out Using the REC Button 3. Press the [PLAY] button to start playback. 4. At the point where you want to punch in, press the [REC] button. 5. At the point where you want to punch out, press the [PLAY] button. 30 Using the REC SELECT buttons 4. Press the [PLAY] button to start playback. 6. At the point where you want to punch out, press the [PLAY] button. 7. Press the [STOP] button to stop playback. Using a Footswitch 32 Auto Punch In/Out Setting the In/Out Points On-the-Fly Page 34 Single Take Auto Punch In/Out 4. Press the [PLAY] button to start the Auto Punch In/Out sequence. Page 36 Auto Punch with a Footswitch 1. Press the [REC SELECT] button (or [GROUP] + [REC SELECT]) of the track A.Pnch Rehe. The AUTO PUNCH IN and OUT indicators appear. This is Auto Punch 4. Press the [REC] button. Multi Take Auto Punch In/Out 38 Page 40 Setting the Pre-Roll & Post-Roll Times Ping-Pong Recording 41 Ping-Pong Recording Destination Track Source Tracks 42 Destination Track Preparing for Ping-Pong This sets the disc playback (track) signal as the source for the channels. 5. Hold down [GROUP] while pressing the [REC SELECT] button of the des- tination track. Rehearsing Ping-Pong Performing Ping-Pong for Real Checking the Ping-Pong Operation 44 Ping-Pong with Overdub Track 7 Track 6 Track 5 Track 4 6. Continue with Preparing for Ping-Pong on page 42. 46 Pitch Adjusting the Pitch Toggling Between FIX & VARI Pitch Using a Footswitch 48 Applying Effects Applying Effects at Mixdown Applying Effects when Recording Applying Effects with Ping-Pong 50 Patching in Signal Processors From processors output To processors input Connect to MD8 INSERT I/O 5 Searching for Songs Rewind & Fast Forward Shuttle Playback Function (Cue/Review) * Searching for the Last Rec IN & OUT Points Searching for Markers Inserting Markers 1. To insert a marker, press the [MARK] button during recording or play- back. MARK X 2. When youve nished, press the [TOC WRITE] button to update the TOC. Marker Indicators Adjusting Markers 1. Press the [ADJUST] button. 2. Use the DATA dial to select the marker that you want to adjust. 3. Press the [ENTER] button. Page 56 Erasing Markers 6 One Song Repeat All Song Repeat 58 AB Repeat Cue List Playback & Copy 60 Program Playback 7 Viewing Disc Contents 62 Erasing Discs Copying & Converting Songs 8T:87654321 64 12. Press the [TOC WRITE] button to update the TOC. Song 2 Song 1 Renumbering Songs The display will show Renum EXE? Before Song Copy After Song Copy Song 2 Song 3 Moving Songs 66 Dividing Songs Combining Songs 68 Erasing Songs Erasing Tracks Erasing Parts 70 Copying Tracks Copying Parts 72 8 Frame Display Display Dimmer Peak Hold 9 Using the MD8 in a Synchronized MIDI System About Tempo Maps 74 Setting Up a Synchronized MIDI System Using MTC Setting the MD8 for MTC Operation Setting the MIDI Sequencer MTC Cabling Note 76 Using MIDI Clock Setting the MIDI Sequencer Programming the Tempo Map Page 78 Selecting MIDI Clock for synchronization 80 Controlling the MD8 with MMC Setting the MMC Device ID Enabling MMC 82 Tempo Map Chart MD8 Applications 83 10 This chapter shows how the MD8 can be used for various applications. One-Take Recording 84 MIDI Home Studio Using the MD8 with Another Mixer 85 Using the MD8 with Another Mixer 8-track digital multitrack MAX. 7mA IN (BAL) TRACK DIRECT OUT MIC/LINE 11 Effects Return EQ Markers Pitch Applications Monitoring 88 Mixdown 12 90 Troubleshooting 92 Appendix MD8 Transport Modes 94 Display Messages Specifications 95 Specications Recorder Mixer 0 dB is referenced to 0.775 V r.m.s. Frequency response EQ Page Block Diagram 97 Block Diagram Page Glossary 100 Page 102 Index Numerics A B C F G H I J N O P Q R S T U V Page Source: Source: Source: Source:Source: Source: Source: Source: Source: Source: 12345678 Tracking Sheet 11-12 97 11 2000 CP Printed in Japan Session Info Marker Log