Manuals / Brands / Home Audio / CD Player / Yamaha / Home Audio / CD Player

Yamaha MDX-E300 SCROLL, SCROLL, SCROLL, DISPLAY, DISPLAY, DISPLAY

1 28

Download 28 pages, 429.74 Kb

PLAYBACK

Switching the display

Press DISPLAY during stop or playback to display other information, such as the remaining time and track titles.

REC/

PAUSESYNC

M-MARK REC MODE INPUT

RANDOM PROGRAM

REPEAT

A-B S/F

DISPLAY SCROLL

POWERSCROLL

DISPLAY

During stop

Press DISPLAY repeatedly to display the following information.

1Number of tracks and total playing time

Total tracks Total playing time

TOTAL

During playback

Press DISPLAY repeatedly to display the following information.

1Current track number and elapsed time

	Track number					Elapsed time
ANALOG	DISC TRACK
ANALOG	DISC TRACK
DIGITAL	TOTAL
OPT.123	REMAIN
COAX.
32 44.1 48	RANDOM	MONO REC			L	–30 –10 –6 4 –2 –1 0 OVER
kHz	PROGRAM	MANUAL			dB –00 –60	–30 –10 –6 4 –2 –1 0 OVER
REPEAT	A-B S F	MANUAL		TOC R

2Time remaining on the current track

REMAIN indicator

TRACK

REMAIN

3Track title

•If the track has not been given a name, “No Title” is displayed.

TRACK

2Time remaining on the MD (only for recordable MDs)

REMAIN indicator

Time remaining on the MD

DISC

REMAIN

Total tracks

3Disc title

DISC

To view the entire disc (track) title

If the disc (track) title is too long to fit in the display, press SCROLL to move the title sequentially across the display. While the title is being displayed, press SCROLL to pause the display, and again to continue presentation of the title. Press and hold SCROLL for rapid presentation of the title.

10

Contents

Page 7Do not plug in this unit to a wall outlet until all connections are complete 8Do not operate this unit upside-down.It may overheat, possibly causing damage 9Do not use excessive force on switches, knobs and/or cords 18VOLTAGE SELECTOR (China and General models only) SPECIAL INSTRUCTIONS FOR U.K. MODEL Front panel Display Remote control System connections Connecting your audio system •Remote control •Batteries (AA, R6, UM-3) •Optical cable •System control cable •Audio pin cable 2Disc insertion slot (P.9) 6REC/PAUSE (P.13) 7Remote control sensor (P.5) 8Display (P.3) 9INPUT (P.13) 3CHAR (P.21) t4 NUMBER (P.21) y5 Numbers [Characters] (P.9/P.21) 9REC/PAUSE (P.13) u0 M-MARK (P.14) Remote control operation range 1 Remove the battery compartment cover 2 Insert batteries into the battery compartment 3 Replace the battery compartment cover Notes CD receiver (CRX-E300) Audio pin cables (included) To wall outlet System control cable Optical cable Receiver (RX-E400) Audio pin cables CD player (CDX-E400) To RX-E400 To AC outlet Amplifier/Receiver CD player (etc.) with with optical IN/OUT optical OUT Preparation •Press STANDBY/ON (POWER on the remote control) to turn this unit on •Select “MD” as the input source of the connected receiver STANDBY/ON To pause DISPLAY SCROLL You can have the unit play all the tracks on a disc in random order RANDOM Press RANDOM Press RANDOM again to turn off the RANDOM indicator or press & Press REPEAT S/F repeatedly to light the REPEAT S or REPEAT F indicators 1 Press &to stop playback 2 Press PROGRAM to light up the PROGRAM indicator 3 Program the desired track by pressing the corresponding number buttons Example: Current programmed When recording on a blank MD To start recording from the end of a previous recording To record over a previous recording Start playing the source to be recorded • If you do not need to adjust the recording level, this step is not necessary 7 Adjust the recording levels. (See “Adjusting recording levels” on this page.) 8 Press #/*(#on the remote control) to start recording •The TOC indicator lights up 9 Start playing the source to be recorded Synchronized start is possible if you make system control connections to INPUT REC MODE 1 Load the sound source into the source component 3 Press SYNC to set this unit to record pause mode 4 Start playing the sound source 1 Press to remove the disc 3 Press REC/PAUSE •“Monitor Out” appears in the display The sound is output from the MD recorder’s analog and digital output terminals Tab To cancel an edit Before editing After editing 1 Press &to set this unit to stop mode 2 Press EDIT repeatedly to display “Disc Erase?”, then press SET/ENTER •“DiscEraseOK?” appears in the display 3 Press SET/ENTER again Example: Erasing track To erase a disc title 2 Press EDIT repeatedly to display “Title Erase?”, then press SET/ENTER •“Disc Title” and “Erase OK?” appear alternatively in the display •The disc title is erased and “Complete” appears momentarily To erase a track title Play the track you want to divide Example: Dividing track dividing 3 Press EDIT repeatedly to display “Divide ?”, then press SET/ENTER 5 Press SET/ENTER +10 1 To title a disc Press &to stop playback To title a track 1Press &to stop playback “Can’t REC!” is displayed before the maximum recording time has been reached “TOC Reading” is displayed continuously Track numbers are not recorded correctly It is not possible to erase part of a track using the A-BERASE function Limitations when recording over an existing track Can’t copy Can’t edit Can’t REC Can’t REC DIG in Unlock SYMPTOM CAUSE REMEDY Digital audio system Inputs Outputs General CAUTION ATTENTION ACHTUNG OBSERVERA ATTENZIONE