Page
7Do not plug in this unit to a wall outlet until all connections are complete
8Do not operate this unit upside-down.It may overheat, possibly causing damage
9Do not use excessive force on switches, knobs and/or cords
18VOLTAGE SELECTOR (China and General models only)
SPECIAL INSTRUCTIONS FOR U.K. MODEL
Front panel
Display
Remote control
System connections
Connecting your audio system
•Remote control
•Batteries (AA, R6, UM-3)
•Optical cable
•System control cable
•Audio pin cable
2Disc insertion slot (P.9)
6REC/PAUSE (P.13)
7Remote control sensor (P.5)
8Display (P.3)
9INPUT (P.13)
3CHAR (P.21)
t4 NUMBER (P.21)
y5 Numbers [Characters] (P.9/P.21)
9REC/PAUSE (P.13)
u0 M-MARK (P.14)
Remote control operation range
1 Remove the battery compartment cover
2 Insert batteries into the battery compartment
3 Replace the battery compartment cover
Notes
CD receiver (CRX-E300)
Audio pin cables (included)
To wall outlet
System control cable
Optical cable
Receiver (RX-E400)
Audio pin cables
CD player (CDX-E400)
To RX-E400
To AC outlet
Amplifier/Receiver
CD player (etc.) with
with optical IN/OUT
optical OUT
Preparation
•Press STANDBY/ON (POWER on the remote control) to turn this unit on
•Select “MD” as the input source of the connected receiver
STANDBY/ON
To pause
DISPLAY
SCROLL
You can have the unit play all the tracks on a disc in random order
RANDOM
Press RANDOM
Press RANDOM again to turn off the RANDOM indicator or press &
Press REPEAT S/F repeatedly to light the REPEAT S or REPEAT F indicators
1 Press &to stop playback
2 Press PROGRAM to light up the PROGRAM indicator
3 Program the desired track by pressing the corresponding number buttons
Example:
Current programmed
When recording on a blank MD
To start recording from the end of a previous recording
To record over a previous recording
Start playing the source to be recorded
• If you do not need to adjust the recording level, this step is not necessary
7 Adjust the recording levels. (See “Adjusting recording levels” on this page.)
8 Press #/*(#on the remote control) to start recording
•The TOC indicator lights up
9 Start playing the source to be recorded
Synchronized start is possible if you make system control connections to
INPUT
REC MODE
1 Load the sound source into the source component
3 Press SYNC to set this unit to record pause mode
4 Start playing the sound source
1 Press to remove the disc
3 Press REC/PAUSE
•“Monitor Out” appears in the display
The sound is output from the MD recorder’s analog and digital output terminals
Tab
To cancel an edit
Before editing
After editing
1 Press &to set this unit to stop mode
2 Press EDIT repeatedly to display “Disc Erase?”, then press SET/ENTER
•“DiscEraseOK?” appears in the display
3 Press SET/ENTER again
Example: Erasing track
To erase a disc title
2 Press EDIT repeatedly to display “Title Erase?”, then press SET/ENTER
•“Disc Title” and “Erase OK?” appear alternatively in the display
•The disc title is erased and “Complete” appears momentarily
To erase a track title
Play the track you want to divide
Example: Dividing track
dividing
3 Press EDIT repeatedly to display “Divide ?”, then press SET/ENTER
5 Press SET/ENTER
+10
1 To title a disc
Press &to stop playback
To title a track
1Press &to stop playback
“Can’t REC!” is displayed before the maximum recording time has been reached
“TOC Reading” is displayed continuously
Track numbers are not recorded correctly
It is not possible to erase part of a track using the A-BERASE function
Limitations when recording over an existing track
Can’t copy
Can’t edit
Can’t REC
Can’t REC
DIG in Unlock
SYMPTOM
CAUSE
REMEDY
Digital audio system
Inputs
Outputs
General
CAUTION
ATTENTION
ACHTUNG
OBSERVERA
ATTENZIONE