Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V2095 Audio/video source equipment, mBasic connections of audio units, (*1): GND terminal (For turntable use)

1 90

Download 90 pages, 1.48 Mb

PREPARATION

Connections

Caution: Plug in this unit and other components after all connections are completed.

All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for each of your components.

Audio/video source equipment

●Use RCA type pin plug cables for audio/video units with the exception described later.

●The output (or input) terminals of YAMAHA audio/video units numbered as 1, 3, 4, etc. on the rear panel must be connected to the same-numbered terminals of this unit.

mBasic connections of audio units

Turntable

OUTPUT

GND

(U.S.A. model)

CD player

MD recorder, Tape deck, etc.

OUTPUT

LINE OUT LINE IN

	AUDIO SIGNAL	AUDIO SIGNAL	VIDEO	VIDEO SIGNAL
			VIDEO	S VIDEO
				S VIDEO
	PHONO	DVD/LD		DVD/LD
	1	TV/DBS		TV/DBS
	CD	TV/DBS		TV/DBS
AM	3	IN		IN
ANT	IN	IN		IN
	(PLAY)
GND	TAPE/MD	VCR 1		VCR 1
GND	4	OUT		OUT
	OUT	OUT		OUT
	OUT
	(REC)
FM	MAIN	IN		IN
ANT	MAIN	IN		IN
ANT
75Ω		VCR 2		VCR 2
75Ω
UNBAL.	SURROUND	OUT		OUT
GND
	EXTERNAL	ZONE 2
	DECODER	ZONE 2
	DECODER	OUT
	INPUT	OUT
	INPUT
	SUB WOOFER CENTER			S VIDEO
				S VIDEO

(*1)

					MONITOR
COAXIAL					OUT
COAXIAL					OPTICAL
			IN	OUT	VIDEO
			IN	OUT
CD	DVD/LD	CD	(PLAY)	TAPE/MD (REC) DVD/LD TV/DBS
			DIGITAL SIGNAL

(*1): GND terminal (For turntable use)

Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected.

: Indicates the direction of signals.

14

Contents

OWNER’S’S MANUAL MODE D’EMPLOI’ SAFETY INSTRUCTIONS Note to CATV system installer: English FCC INFORMATION (for US customers only) We Want You Listening For A Lifetime Page CONTENTS SAFETY INSTRUCTIONS Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit INTRODUCTION Power, 0.02% THD, 20–20,000Hz What’s DSP Introduction Digital Sound Field Processing Dolby Pro Logic Surround Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Front panel 7 890 AB C D E F G H I J K L M N Page Display panel PREPARATION mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Audio/video source equipment mBasic connections of audio units (*1): GND terminal (For turntable use) mBasic connections of video units VIDEO AUX terminals (on the front panel) mConnecting to digital (OPTICAL and COAXIAL) terminals <U.S.A. and Canada models <Australia, China, Singapore and General models mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player <For Australia, China, Singapore and General models only <For U.S.A. and Canada models only mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal Antennas mConnecting the AM loop antenna mConnecting the indoor FM antenna GND terminal mOptional outdoor AM antenna mOptional outdoor FM antenna AC OUTLET(S) Voltage Selector (China and General Models only) On screen display Selecting a type of display 1. SPEAKER SET 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections 3, 4 Speaker balance adjustment CONTINUED Page 11 BASIC OPERATION CONTINUED Page When you finish using this unit mSwitching the input mode <U.S.A. and Canada models only AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) 3, 5 Sound control Tuning Preset tuning mManual preset tuning To store stations To recall a preset station mAutomatic preset tuning If you want to make the automatic preset tuning toward lower frequencies; When the automatic preset tuning is finished To recall a preset station mExchanging preset stations Using digital sound field processor (DSP) Playing a source with an effect of the digital sound field processor (DSP) Page mTo cancel the effect sound C E N T E R L S U R F R O N T mMethod of adjustment Speakers Control range (dB) Preset value Brief overview of digital sound field programs mProgram No. 1 to 7: Hi-FiDSP programs (for audio sources) Page mProgram No. 8 to 12: CINEMA-DSPprograms (for Audio/Video sources) Page Page ADVANCED FEATURES 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields What is a sound field The elements of a sound field mSelecting and editing program parameters 4, 5 P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer To set the SLEEP time SLEEP OFF To cancel the SLEEP timer REMOTE CONTROLLER Page Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Setting the MACRO switch OFF Page Methods of learning and clearing functions mLearning a new function mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions CUSTOM INSTALLATION GUIDE ZONE 2 remote controller Key name and function Display panel information TROUBLESHOOTING Remote controller Tuner When playing back a source encoded with DTS: SPECIFICATIONS AM SECTION GENERAL