Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V2095 CUSTOM INSTALLATION GUIDE, English, Example of system configuration and connections

1 90

Download 90 pages, 1.48 Mb

CUSTOM INSTALLATION GUIDE

You can make up a dual-room audio/video system with this unit. In this system, you can make this unit send audio and video signals to the main room’s equipment (speakers and TV monitor) and the second room’s equipment (amplifier and TV monitor) respectively. For example, you can enjoy listening to a CD source in the main room while another person is enjoying watching an LD source in the second room.

By using the ZONE 2 remote controller in the second room, you can enjoy a source which is different from the one being selected in the main room.

English

Connections

The following optional products are required to use the dual- room function.

1An infrared emitter in the main room

This emitter emits the infrared signals transmitted by the ZONE 2 remote controller in the second room to the other components in the main room (for example, CD player or LD player).

2An amplifier, TV monitor and speakers for the second room

3 An infrared signal receiver for the second room

(*1): Some Yamaha models can be connected to this unit’s REMOTE CONTROL OUT terminals. If you connect these units in series, the use of an infrared emitter may not be necessary.

This unit

OUT		IN OUT		IN OUT
OUT		IN OUT		IN OUT

Up to 6 units can be connected in this connecting way.

Note

Since there are so many ways to connect and use this unit in a dual-room system, we recommend that you consult with a custom installation specialist for connections which will best meet your requirements.

Example of system configuration and connections

Main Room

LD player etc. (*1)

This unit

VIDEO SIGNAL ZONE 2 OUT	AUDIO SIGNAL ZONE 2 OUT
OUT	IN

Second Room

2

Amplifier

TV monitor

ZONE 2 remote controller

1 Infrared emitter

REMOTE CONTROL

REMOTE CONTROL

3Infrared signal receiver

Note on adjusting the volume

First set the volume for the second room at “–16” or “–17” by using the VOLUME ZONE 2 keys on the ZONE 2 remote controller. The level can be checked on the display of this unit. (This operation can be made by directing the ZONE 2 remote controller to this unit.)

After this setting is made, use the volume control on the amplifier in the second room to adjust the volume for the second room.

79

Contents

OWNER’S’S MANUAL MODE D’EMPLOI’ SAFETY INSTRUCTIONS Note to CATV system installer: English FCC INFORMATION (for US customers only) We Want You Listening For A Lifetime Page CONTENTS SAFETY INSTRUCTIONS Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit INTRODUCTION Power, 0.02% THD, 20–20,000Hz What’s DSP Introduction Digital Sound Field Processing Dolby Pro Logic Surround Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Front panel 7 890 AB C D E F G H I J K L M N Page Display panel PREPARATION mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Audio/video source equipment mBasic connections of audio units (*1): GND terminal (For turntable use) mBasic connections of video units VIDEO AUX terminals (on the front panel) mConnecting to digital (OPTICAL and COAXIAL) terminals <U.S.A. and Canada models <Australia, China, Singapore and General models mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player <For Australia, China, Singapore and General models only <For U.S.A. and Canada models only mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal Antennas mConnecting the AM loop antenna mConnecting the indoor FM antenna GND terminal mOptional outdoor AM antenna mOptional outdoor FM antenna AC OUTLET(S) Voltage Selector (China and General Models only) On screen display Selecting a type of display 1. SPEAKER SET 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections 3, 4 Speaker balance adjustment CONTINUED Page 11 BASIC OPERATION CONTINUED Page When you finish using this unit mSwitching the input mode <U.S.A. and Canada models only AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) 3, 5 Sound control Tuning Preset tuning mManual preset tuning To store stations To recall a preset station mAutomatic preset tuning If you want to make the automatic preset tuning toward lower frequencies; When the automatic preset tuning is finished To recall a preset station mExchanging preset stations Using digital sound field processor (DSP) Playing a source with an effect of the digital sound field processor (DSP) Page mTo cancel the effect sound C E N T E R L S U R F R O N T mMethod of adjustment Speakers Control range (dB) Preset value Brief overview of digital sound field programs mProgram No. 1 to 7: Hi-FiDSP programs (for audio sources) Page mProgram No. 8 to 12: CINEMA-DSPprograms (for Audio/Video sources) Page Page ADVANCED FEATURES 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields What is a sound field The elements of a sound field mSelecting and editing program parameters 4, 5 P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer To set the SLEEP time SLEEP OFF To cancel the SLEEP timer REMOTE CONTROLLER Page Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Setting the MACRO switch OFF Page Methods of learning and clearing functions mLearning a new function mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions CUSTOM INSTALLATION GUIDE ZONE 2 remote controller Key name and function Display panel information TROUBLESHOOTING Remote controller Tuner When playing back a source encoded with DTS: SPECIFICATIONS AM SECTION GENERAL