Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V2095 Antennas, mConnecting the AM loop antenna

1 90

Download 90 pages, 1.48 Mb

PREPARATION

Antennas

●Each antenna should be connected to the designated terminals correctly, as shown in the following figure.

●Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality only with the indoor antennas, the use of an outdoor antenna may result in improvement.

			Outdoor AM antenna
	Indoor FM
	antenna
Outdoor FM antenna	(included)
Outdoor FM antenna
						AM loop
						antenna
			(U.S.A. model)			(included)
			(U.S.A. model)
			AUDIO SIGNAL
			PHONO
			1
			CD
		AM	3
		ANT	IN
			(PLAY)
	75-ohm/300-ohm	GND	TAPE/MD
	75-ohm/300-ohm	GND	4
	antenna adapter		4
	antenna adapter		OUT
			(REC)
	75-ohm coaxial cable	FM	MAIN
		ANT	MAIN
		ANT
		75Ω
		UNBAL.	SURROUND
		GND
			EXTERNAL
			DECODER
			INPUT
			SUB WOOFER	CENTER
	75-ohm/300-ohm	COAXIAL
	75-ohm/300-ohm
	antenna adapter			IN	OUT
		CD	DVD/LD CD	(PLAY) TAPE/MD (REC)
				DIGITAL SIGNAL
	300-ohm flat
	ribbon cable					Ground
						Ground

English

mConnecting the AM loop antenna

1.Press the tab and unlock the terminal hole.

2.Connect the AM loop antenna lead wires to the AM ANT and GND terminals.

3.Return the tab back to the original position to lock the lead wires. Lightly pull on the lead wires to confirm a good connection.

1

3

2

4. Attach the loop antenna to the antenna stand.

Loop antenna

Antenna stand

5.Orient the AM loop antenna so that the best reception is obtained.

Notes

●The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.

●The AM loop antenna should be kept connected, even if an

outdoor AM antenna is connected to this unit.

25

Contents

OWNER’S’S MANUAL MODE D’EMPLOI’ SAFETY INSTRUCTIONS Note to CATV system installer: English FCC INFORMATION (for US customers only) We Want You Listening For A Lifetime Page CONTENTS SAFETY INSTRUCTIONS Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit INTRODUCTION Power, 0.02% THD, 20–20,000Hz What’s DSP Introduction Digital Sound Field Processing Dolby Pro Logic Surround Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Front panel 7 890 AB C D E F G H I J K L M N Page Display panel PREPARATION mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Audio/video source equipment mBasic connections of audio units (*1): GND terminal (For turntable use) mBasic connections of video units VIDEO AUX terminals (on the front panel) mConnecting to digital (OPTICAL and COAXIAL) terminals <U.S.A. and Canada models <Australia, China, Singapore and General models mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player <For Australia, China, Singapore and General models only <For U.S.A. and Canada models only mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal Antennas mConnecting the AM loop antenna mConnecting the indoor FM antenna GND terminal mOptional outdoor AM antenna mOptional outdoor FM antenna AC OUTLET(S) Voltage Selector (China and General Models only) On screen display Selecting a type of display 1. SPEAKER SET 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections 3, 4 Speaker balance adjustment CONTINUED Page 11 BASIC OPERATION CONTINUED Page When you finish using this unit mSwitching the input mode <U.S.A. and Canada models only AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) 3, 5 Sound control Tuning Preset tuning mManual preset tuning To store stations To recall a preset station mAutomatic preset tuning If you want to make the automatic preset tuning toward lower frequencies; When the automatic preset tuning is finished To recall a preset station mExchanging preset stations Using digital sound field processor (DSP) Playing a source with an effect of the digital sound field processor (DSP) Page mTo cancel the effect sound C E N T E R L S U R F R O N T mMethod of adjustment Speakers Control range (dB) Preset value Brief overview of digital sound field programs mProgram No. 1 to 7: Hi-FiDSP programs (for audio sources) Page mProgram No. 8 to 12: CINEMA-DSPprograms (for Audio/Video sources) Page Page ADVANCED FEATURES 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields What is a sound field The elements of a sound field mSelecting and editing program parameters 4, 5 P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer To set the SLEEP time SLEEP OFF To cancel the SLEEP timer REMOTE CONTROLLER Page Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Setting the MACRO switch OFF Page Methods of learning and clearing functions mLearning a new function mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions CUSTOM INSTALLATION GUIDE ZONE 2 remote controller Key name and function Display panel information TROUBLESHOOTING Remote controller Tuner When playing back a source encoded with DTS: SPECIFICATIONS AM SECTION GENERAL