Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V620 TUNING, Connecting the Antennas, ■Connecting the indoor FM antenna, ■Connecting the AM loop antenna 3, BASIC, outlet, English, OPERATION, models only)

1 79

Download 79 pages, 2.84 Mb

TUNING

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

FREQUENCY STEP switch (China and General

models only)
	STEP	Because the interstation frequency spacing
	FREQUENCY	differs in different areas, set the
	FM/AM	differs in different areas, set the
	/10KHZ	FREQUENCY STEP switch (locating at
	100KHZ	the rear) according to the frequency
	/9KHZ	the rear) according to the frequency
	50KHZ
		spacing in your area.
		North, Central and South America:
		100 kHz/10 kHz
		Other area: 50 kHz/9 kHz
		Before setting this switch, disconnect the
		AC power plug of this unit from the AC
		outlet.

AM loop		Indoor FM
antenna		antenna
(included)		(included)

	(U.S.A. model)
	TUNER
AM ANT GND	FM ANT
	75 UNBAL.

Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the indoor FM antennaConnect the included indoor FM antenna to the FM ANT 75Ω UNBAL. terminal.

Note

•Do not connect an outdoor FM antenna and the indoor FM antenna at the same time.

■Connecting the AM loop antenna 3 1

42

5

Antenna stand

1Press and hold the tab to unlock the terminal hole.2Insert the AM loop antenna lead wires into the AM ANT and GND terminals.3Release the tab to lock the lead wires.Lightly pull the lead wires to confirm a good connection.4Attach the loop antenna to the antenna stand.5Orient the AM loop antenna so that the best reception is obtained.

y

•The AM loop antenna can be removed from the stand and attached to a wall, etc.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

OPERATION	BASIC

English

29

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Checking the Package Contents Installing Batteries in the Remote Control CONTROLS AND FUNCTIONS Front Panel 8BASS Adjusts the low-frequencyresponse for the left and right main speakers 9TREBLE Adjusts the high-frequencyresponse for the left and right main speakers 0SPEAKERS A/B Remote Control Description of the Numeric Buttons Using the Remote Control Front Panel Display Rear Panel SPEAKER SETUP Speakers to Be Used Speaker Placement CONNECTIONS Before Connecting Components Connecting Audio Components Connecting an External Decoder Connecting Video Components When using an LD player Connecting the Speakers ■SUBWOOFER jack IMPEDANCE SELECTOR Switch Connecting the Power Supply Cords ON-SCREENDISPLAY (OSD) OSD Modes P01 CONCERT HALL Selecting the OSD Mode SPEAKER MODE SETTINGS Summary of SPEAKER SET Items 1A through 1E ADJUSTING THE SPEAKER OUTPUT LEVELS Before You Begin SUR.) TEST DOLBY SUR 4 Press LEVEL repeatedly to select the speaker to be adjusted 5Press j / i repeatedly to adjust the output level of •While adjusting, the test tone is heard from the selected speaker 6When the adjustment is complete, press BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5Adjust the volume to the desired output level ■To mute the sound Use this when you want to temporarily mute audio output Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– Input Modes and Indications ■Notes on playing a source encoded with a DTS signal Selecting a Sound Field Program Normal Stereo Reproduction TUNING Connecting the Antennas Automatic (or Manual) Tuning Presetting Stations Tuning in to a Preset Station Exchanging Preset Stations BASIC RECORDING SET MENU Adjusting the Items on the SET MENU SET MENU 1/3 4A CMPNT-VINPUT 1SPEAKER SET (speaker mode settings) 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D LFE/BASS OUT 1E MAIN LEVEL 2 L/R BALANCE 3 HP TONE CTRL 4 I/O ASSIGNMENT 4C OPTICAL IN 4D COAXIAL IN 5 INPUT MODE (initial input mode) 6DOLBY D. SET (Dolby Digital set) 6 DOLBY D. SET 7 DTS SET (DTS LFE level) 7 DTS SET 8 SP DELAY TIME 8 SP DELAY TIME 9 DISPLAY SET 9 DISPLAY SET 10 MEMORY GUARD ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER Setting the Sleep Timer Canceling the Sleep Timer REMOTE CONTROL FEATURES Selector Dial Commonly Used Buttons in Any Position of the Selector Dial Controlling the Components Connected to This Unit Button Names and Functions in Each Position ■DVD/LD position ■DVD MENU position • DVD MENU operations cannot be performed for some DVD players ■ VCR position ■ CBL/SAT position ■TV position Setting the Manufacturer Code Returning to the Factory Setting SOUND FIELD PROGRAM Hi-FiDSP Programs CINEMA DSP Programs ■For movie programs: Nos. 7 to Program Input source (group) MOVIE ■MOVIE THEATER 1 and When the input source is analog, PCM or encoded with Dolby Digital in 2-channel 70 mm SPECTACLE 70 mm SCI-FI 70 mm ADVENTURE SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field Sound Field Program Parameters Changing Parameter Settings P07 MOVIE THEATER Resetting a Parameter to the Factory-setValue Sound Field Parameter Descriptions ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■S.ROOM SIZE (surround room size) ■S.LIVENESS (surround liveness) ■CT.DELAY (center delay) 0 – 50 msec ■LS.DELAY (left surround delay) TROUBLESHOOTING Page English APPENDIX ■Tuner ■Remote control SPECIFICATIONS GLOSSARY ■S VIDEO signal ■Component video signal ■PCM (Linear PCM) ■Sampling frequency and number of quantized bits ■I/O assignment (SET MENU) INDEX LIST OF MANUFACTURER CODES LISTES DES CODES FABRICANT CABLE TV SATELLITE TUNER (DSS) VCR DVD PLAYER LD PLAYER CD PLAYER CD RECORDER/CD- RW MD RECORDER TAPE DECK Page OPTICAL AUDIO OUT S VIDEO VIDEO COMPONENT Analog signal Optical signal S Video signal Video signal Signal flow Quick Reference Card AMP/TUN DSP/TUN TAPE/MD (CD-R) DVD/LD DVD MENU VCR CBL/SAT