Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V757 ■Connecting to an external amplifier, 1FRONT PRE OUT jacks, 3CENTER PRE OUT jack, 2SURROUND PRE OUT jacks, 5SUBWOOFER PRE OUT jack

1 107

Download 107 pages, 1.89 Mb

CONNECTIONS

■Connecting to an external amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the PRE OUT jacks as follows.

Notes

•When audio pin plugs are connected to the PRE OUT jacks for output to an external amplifier, do not make connections to the corresponding SPEAKERS terminals. Set the volume of the amplifier connected to this unit to the maximum.

•The signals output through the FRONT PRE OUT and CENTER PRE OUT jacks are affected by the TONE CONTROL settings.

•If SPEAKERS A is turned off and SP B is set to ZONE B (see page 72), signals will only be output from the FRONT PRE OUT jacks.

1	2 3	4
	PRE OUT
	CENTER	SINGLE
	SUB	SURROUND
FRONT	SURROUND WOOFER	BACK

5

1FRONT PRE OUT jacks

Front channel line output jacks.

2SURROUND PRE OUT jacks

Surround channel line output jacks.

3CENTER PRE OUT jack

Center channel line output jack.

4SURROUND BACK PRE OUT jacks

Surround back or presence channel line output jacks.

5SUBWOOFER PRE OUT jack

Connect a subwoofer with built-in amplifier, such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.

Notes

•Each PRE OUT jack outputs the same channel signals as the corresponding speaker terminals.

•Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level using the remote control (see “Manually adjusting speaker levels” on page 60).

•Some signals may not be output from the SUBWOOFER PRE OUT jack depending on the SPEAKER SET (see page 64) and LFE/BASS OUT (see page 65) settings.

20

Contents

Page IMPORTANT SAFETY INSTRUCTIONS Note to CATV system installer: FCC INFORMATION (for US customers) 1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT NOTE: CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES Built-in 7-channelpower amplifier Sound field features Sophisticated AM/FM tuner Other features GETTING STARTED Supplied accessories Installing batteries in the remote control Notes on batteries CONTROLS AND FUNCTIONS Front panel ■U.S.A., Canada, Australia and Europe models only Remote control Using the remote control ■Handling the remote control Front panel display ■U.S.A., Canada, Australia and Europe model only Rear panel ■General models only SPEAKER SETUP Speaker placement Surround speakers (SR and SL) Surround back speakers (SBR and SBL) Subwoofer Speaker connections ■Connecting to PRESENCE/ZONE 2 or PRESENCE speaker terminals ■Banana plug connections Page ■FRONT terminals ■CENTER terminals ■SURROUND terminals ■SUBWOOFER jack ■SURROUND BACK terminals CONNECTIONS Before connecting components ■Cable indications ■Analog jacks ■Digital jacks Connecting video components ■Connections for DVD playback ■Connecting to the MULTI CH INPUT jacks ■Connections for other video components ■ VIDEO AUX jacks (on the front panel) Connecting audio components ■Connections for audio components ■Connecting a turntable ■Connecting to an external amplifier Connecting the FM and AM antennas ■FREQUENCY STEP (General model only) ■Connecting the AM loop antenna ■Connecting the AC power cord ■AC OUTLET(S) (SWITCHED) ■VOLTAGE SELECTOR (General model only) ■Memory back-up Speaker impedance setting Turning on the power AUTO SETUP Introduction Optimizer microphone setup Starting the setup ■If an error screen appears ■If a warning screen appears ■Troubleshooting for auto setup procedure Warnings after auto setup Warning message PLAYBACK Basic operations ■To adjust the tone ■To listen with headphones (“SILENT CINEMA”) ■To mute the sound ■Selecting MULTI CH INPUT Selecting sound field programs ■Front panel operation ■Remote control operation ■Enjoying multi-channelsoftware ■Enjoying 2-channelsoftware in surround ■Listening to high fidelity stereo sound (PURE DIRECT) ■Night listening modes ■Downmixing to 2 channels ■Listening to unprocessed input signals ■Virtual CINEMA DSP Selecting input modes ■Displaying information about the input source 3Press u / d to display the following information about the input signal FM/AM TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting FM stations ■Manually presetting stations Automatic preset tuning options: Selecting preset stations Exchanging preset stations 4Press PRESET/TUNING (EDIT) again XM SATELLITE RADIO TUNING What is XM Satellite Radio XM Satellite Radio connections ■Connecting the XM connect and Play digital antenna accessory XM Satellite Radio functions ■Front panel functions ■Remote control functions Activating XM Satellite Radio Basic XM Satellite Radio operations ■Selecting the XM Satellite Radio mode ■Switching XM information in the front panel display ■Displaying XM information in the on XM Satellite Radio search modes ■All Channel Search mode ■Category Search mode ■Preset Search mode ■Direct Number Access mode Setting XM Satellite Radio preset channels While the MEMORY indicator is flashing, press PRESET/TUNING/CH ■Status and error messages RECORDING ■Special considerations when recording DTS software SOUND FIELD PROGRAM DESCRIPTIONS For movie/video sources Page For music sources ADVANCED OPERATIONS Selecting the OSD mode Using the sleep timer ■Setting the sleep timer ■Canceling the sleep timer Manually adjusting speaker levels SET MENU ■AUTO SETUP ■MANUAL SETUP ■SIGNAL INFO Using SET MENU 1 SOUND MENU ■Speaker settings A)SPEAKER SET Surround back speakers SUR. B L/R SP SMLx2 Presence speakers PRESENCE SP NONE Bass out Speaker level ■Speaker distance C)SP DISTANCE ■Center graphic equalizer D)EQUALIZER ■Low-frequencyeffect level E)LFE LEVEL ■Audio settings G)AUDIO SET Dynamic range 2 INPUT MENU ■Input/output assignment ) and B ) and and Input mode Volume Trim Input rename 3 OPTION MENU ■Display settings A)DISPLAY SET Memory guard ■Parameter initialization C)PARAM. INI Zone set Speaker B setting SP B ■XM Radio setting E)XM RADIO SET ADVANCED SETUP MENU ■ADVANCED SETUP menu items REMOTE CONTROL FEATURES Control area ■Controlling this unit ■Controlling other components Setting remote control codes 3Press u / d to select the name of your component’s manufacturer 5Press LEARN again to exit from the setup mode Controlling other components Programming codes from other remote controls Changing source names in the display window Clearing function sets Clearing individual functions ■Clearing a learned function ONLY) Zone 2 connections ■System configuration and connections example Remote controlling Zone ■To enable Zone 2 mode on the remote control ■To control Zone ■Turning this unit to either on or standby ■Special considerations for DTS software EDITING SOUND FIELD PARAMETERS What is a sound field Changing parameter settings ■Elements of a sound field ■Resetting parameters to the factory presets SOUND FIELD PARAMETER DESCRIPTIONS ■DSP LEVEL (DSP level) ■INIT. DLY/P. INIT. DLY (Initial delay) ■ROOM SIZE/P. ROOM SIZE (Room size) ■LIVENESS (Liveness) ■S. INIT. DLY (Surround initial delay) ■S. ROOM SIZE (Surround room size) ■S. LIVENESS (Surround liveness) ■SB INI. DLY (Surround back initial delay) ■REV.TIME (Reverberation time) ■REV.DELAY (Reverberation delay) ■REV. LEVEL (Reverberation level) ■DIALG.LIFT (Dialog lift) For 2ch Stereo: ■DIRECT (Direct) For 7ch Stereo: ■CT LEVEL (Center level) For DTS Neo:6 Music: ■C. IMAGE (Center image) TROUBLESHOOTING ■General Page Page ■Tuner ■Remote control RESETTING THE FACTORY PRESETS GLOSSARY Audio formats ■Dolby Digital ■Dolby Digital EX ■Dolby Pro Logic Sound field programs ■CINEMA DSP ■SILENT CINEMA Audio information ■ITU-R Video signal information ■Component video signal ■Composite video signal ■S-videosignal SPECIFICATIONS