REMOTE CONTROL FEATURES

Setting remote control codes

You can control other components by setting the appropriate manufacturer codes. Codes can be set up for each input area.

The following table shows the factory preset component (Library: component category) and the manufacturer code for each area.

Remote Control Code Default Settings

 

Component

 

Input area

category

Manufacturer

 

(Library)

 

 

 

 

A

LD

Yamaha (U.K. and Europe models)

Yamaha-1 (Other models)

 

 

 

 

 

B

CD-R

Yamaha

 

 

 

PHONO

TV

–

 

 

 

V-AUX

VCR

–

 

 

 

TUNER

TUNER

Yamaha-3 (U.K. and Europe models)

Yamaha-4 (Other models)

 

 

 

 

 

MD/CD-R

MD

Yamaha-1

 

 

 

CD

CD

Yamaha-1

 

 

 

DTV/CBL

TV

–

 

 

 

VCR 1

VCR

–

 

 

 

DVR/VCR2

DVR

Yamaha

 

 

 

DVD

DVD

Yamaha-1

 

 

 

Note

You may not be able to operate your YAMAHA component even if a YAMAHA remote control code is initially set as listed above. In this case, try to set other YAMAHA remote control code(s).

1Press an input selector button to select the source component you want to set up.

A

B

PHONO

MULTI CH IN

V-AUX

TUNER

MD/CD-R

CD

DTV/CBL

VCR 1

DVR/VCR2

DVD

2Press and hold LEARN for about 3 seconds using a ballpoint pen or similar object.

“SETUP” and the selected component name appear alternately in the display window.

LEARN

Be sure to press and hold LEARN for at least 3 seconds, otherwise the learning process will start.

y

Complete each of the following steps in 30 seconds. Otherwise, the learning mode will be automatically canceled. In this case, press LEARN again.

If you want to change a library (component category), press j / i. You can set a different type of component.

Library choices: L:DVD, L:DVR, L:LD, L:CD, L:CDR, L:MD, L:TAP (tape), L:TUN, L:AMP*, L:TV, L:CAB (cable), L:DBS, L:SAT, L:VCR

•The amplifier Library (L:AMP) code is preset to “ID1” to operate this unit. However, you can switch between the following two codes if necessary.

The initial setting for “Amplifier library” is “ID1”.

AMP library

 

Remote

code

 

control ID

(remote

Function

(this unit’s

control

 

setting: see

setting)

 

page 74)

 

 

 

ID1

To operate this unit using the

 

(initial setting)

default code.

 

 

 

 

ID1Z

To operate this unit using the

ID1

 

default code.

 

(initial

 

To operate Zone 2 or Zone 3

 

setting)

 

features (see page 83).

 

 

 

(U.S.A., Canada, Europe and

 

 

Australia models only)

 

 

 

 

ID2

To operate this unit using an

 

alternative code.

 

 

 

 

 

 

 

To operate this unit using an

 

 

alternative code.

ID2

 

To operate Zone 2 or Zone 3

ID2Z

 

features (see page 83).

 

 

 

 

(U.S.A., Canada, Europe and

 

 

Australia models only)

 

 

 

 

When using multiple YAMAHA receivers/amplifiers, you may be able to operate the other components simultaneously with the default code setting. In this case, set one of the alternative codes to operate this unit separately

76