Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V757 Connecting the FM and AM antennas, ■FREQUENCY STEP (General model only), ■Connecting the AM loop antenna, PREPARATION

1 107

Download 107 pages, 1.89 Mb

CONNECTIONS

Connecting the FM and AM antennas

Both FM and AM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Indoor FM antenna

(included)AM loop antenna (included)

TUNER

75Ω UNBAL.

FM

ANT

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■FREQUENCY STEP (General model only)

Be sure to set the frequency step according to the frequency spacing in your area (see page 73).

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should al ways be connected, even if an outdoor AM antenna is connected to this unit.

•A properly installed outdoor an tenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

PREPARATION

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it to the terminals on this unit.

2Press and hold the tab to insert the AM loop antenna

lead wires into the AM ANT and GND terminals.

3Orient the AM loop antenna for the best reception.

21

Contents

Page IMPORTANT SAFETY INSTRUCTIONS Note to CATV system installer: FCC INFORMATION (for US customers) 1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT NOTE: CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES Built-in 7-channelpower amplifier Sound field features Sophisticated AM/FM tuner Other features GETTING STARTED Supplied accessories Installing batteries in the remote control Notes on batteries CONTROLS AND FUNCTIONS Front panel ■U.S.A., Canada, Australia and Europe models only Remote control Using the remote control ■Handling the remote control Front panel display ■U.S.A., Canada, Australia and Europe model only Rear panel ■General models only SPEAKER SETUP Speaker placement Surround speakers (SR and SL) Surround back speakers (SBR and SBL) Subwoofer Speaker connections ■Connecting to PRESENCE/ZONE 2 or PRESENCE speaker terminals ■Banana plug connections Page ■FRONT terminals ■CENTER terminals ■SURROUND terminals ■SUBWOOFER jack ■SURROUND BACK terminals CONNECTIONS Before connecting components ■Cable indications ■Analog jacks ■Digital jacks Connecting video components ■Connections for DVD playback ■Connecting to the MULTI CH INPUT jacks ■Connections for other video components ■ VIDEO AUX jacks (on the front panel) Connecting audio components ■Connections for audio components ■Connecting a turntable ■Connecting to an external amplifier Connecting the FM and AM antennas ■FREQUENCY STEP (General model only) ■Connecting the AM loop antenna ■Connecting the AC power cord ■AC OUTLET(S) (SWITCHED) ■VOLTAGE SELECTOR (General model only) ■Memory back-up Speaker impedance setting Turning on the power AUTO SETUP Introduction Optimizer microphone setup Starting the setup ■If an error screen appears ■If a warning screen appears ■Troubleshooting for auto setup procedure Warnings after auto setup Warning message PLAYBACK Basic operations ■To adjust the tone ■To listen with headphones (“SILENT CINEMA”) ■To mute the sound ■Selecting MULTI CH INPUT Selecting sound field programs ■Front panel operation ■Remote control operation ■Enjoying multi-channelsoftware ■Enjoying 2-channelsoftware in surround ■Listening to high fidelity stereo sound (PURE DIRECT) ■Night listening modes ■Downmixing to 2 channels ■Listening to unprocessed input signals ■Virtual CINEMA DSP Selecting input modes ■Displaying information about the input source 3Press u / d to display the following information about the input signal FM/AM TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting FM stations ■Manually presetting stations Automatic preset tuning options: Selecting preset stations Exchanging preset stations 4Press PRESET/TUNING (EDIT) again XM SATELLITE RADIO TUNING What is XM Satellite Radio XM Satellite Radio connections ■Connecting the XM connect and Play digital antenna accessory XM Satellite Radio functions ■Front panel functions ■Remote control functions Activating XM Satellite Radio Basic XM Satellite Radio operations ■Selecting the XM Satellite Radio mode ■Switching XM information in the front panel display ■Displaying XM information in the on XM Satellite Radio search modes ■All Channel Search mode ■Category Search mode ■Preset Search mode ■Direct Number Access mode Setting XM Satellite Radio preset channels While the MEMORY indicator is flashing, press PRESET/TUNING/CH ■Status and error messages RECORDING ■Special considerations when recording DTS software SOUND FIELD PROGRAM DESCRIPTIONS For movie/video sources Page For music sources ADVANCED OPERATIONS Selecting the OSD mode Using the sleep timer ■Setting the sleep timer ■Canceling the sleep timer Manually adjusting speaker levels SET MENU ■AUTO SETUP ■MANUAL SETUP ■SIGNAL INFO Using SET MENU 1 SOUND MENU ■Speaker settings A)SPEAKER SET Surround back speakers SUR. B L/R SP SMLx2 Presence speakers PRESENCE SP NONE Bass out Speaker level ■Speaker distance C)SP DISTANCE ■Center graphic equalizer D)EQUALIZER ■Low-frequencyeffect level E)LFE LEVEL ■Audio settings G)AUDIO SET Dynamic range 2 INPUT MENU ■Input/output assignment ) and B ) and and Input mode Volume Trim Input rename 3 OPTION MENU ■Display settings A)DISPLAY SET Memory guard ■Parameter initialization C)PARAM. INI Zone set Speaker B setting SP B ■XM Radio setting E)XM RADIO SET ADVANCED SETUP MENU ■ADVANCED SETUP menu items REMOTE CONTROL FEATURES Control area ■Controlling this unit ■Controlling other components Setting remote control codes 3Press u / d to select the name of your component’s manufacturer 5Press LEARN again to exit from the setup mode Controlling other components Programming codes from other remote controls Changing source names in the display window Clearing function sets Clearing individual functions ■Clearing a learned function ONLY) Zone 2 connections ■System configuration and connections example Remote controlling Zone ■To enable Zone 2 mode on the remote control ■To control Zone ■Turning this unit to either on or standby ■Special considerations for DTS software EDITING SOUND FIELD PARAMETERS What is a sound field Changing parameter settings ■Elements of a sound field ■Resetting parameters to the factory presets SOUND FIELD PARAMETER DESCRIPTIONS ■DSP LEVEL (DSP level) ■INIT. DLY/P. INIT. DLY (Initial delay) ■ROOM SIZE/P. ROOM SIZE (Room size) ■LIVENESS (Liveness) ■S. INIT. DLY (Surround initial delay) ■S. ROOM SIZE (Surround room size) ■S. LIVENESS (Surround liveness) ■SB INI. DLY (Surround back initial delay) ■REV.TIME (Reverberation time) ■REV.DELAY (Reverberation delay) ■REV. LEVEL (Reverberation level) ■DIALG.LIFT (Dialog lift) For 2ch Stereo: ■DIRECT (Direct) For 7ch Stereo: ■CT LEVEL (Center level) For DTS Neo:6 Music: ■C. IMAGE (Center image) TROUBLESHOOTING ■General Page Page ■Tuner ■Remote control RESETTING THE FACTORY PRESETS GLOSSARY Audio formats ■Dolby Digital ■Dolby Digital EX ■Dolby Pro Logic Sound field programs ■CINEMA DSP ■SILENT CINEMA Audio information ■ITU-R Video signal information ■Component video signal ■Composite video signal ■S-videosignal SPECIFICATIONS