Yamaha YPP-200 Connecting to a Personal Computer, Using the MIDI Functions

36

YPP-200

Connecting to a Personal Computer

By connecting your YPP-200’s MIDI terminals to a personal computer, you can have

access to a wide variety of music software.

When using a MIDI interface device installed in the personal computer, connect the MIDI

terminals of the personal computer and the YPP-200.

Use only special MIDI cables when connecting MIDI devices.

●When using a MIDI interface with a Macintosh series computer, connect the

RS-422 terminal of the computer (modem or printer terminal) to the MIDI

interface, as shown in the diagram below.

MIDI INMIDI OUT

MIDI OUTMIDI IN

YPP-200

●Connect the MIDI terminals of the YPP-200 to the MIDI terminals of the per-

sonal computer.

●When connecting to a computer with a USB interface, use the Yamaha UX256

USB/MIDI Interface. Connect the UX256 and the computer with a standard

USB cable, then make the proper MIDI connections between the YPP-200 and

the UX256.

MIDI IN

RS-422

MIDI OUT

MIDI Interface

YPP-200

MIDI IN

USB Cable

MIDI OUT

UX 256

YPP-200

•When connecting the YPP-200 to a personal computer, first turn the power to both the YPP-200 and

the computer OFF before connecting the cable. After connecting the cable, turn the power to the

computer on first, then turn on the YPP-200.

•When using a Macintosh series computer, set the MIDI interface clock setting in the application

software to match the setting of the MIDI interface you are using. For details, refer to the owner’s

manual for the software you are using.

Computer

(sequencer software)

Computer

(sequencer software)

Computer

(sequencer software) USB Cable

Using the MIDI Functions

Contents

Main WARNING: SPECIFICATIONS SUBJECT TO CHANGE: NOTICE: ENVIRONMENTAL ISSUES: SPECIAL MESSAGE SECTION PLEASE KEEP THIS MANUAL FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! 2. IMPORTANT: When connecting this product to accessories and/ 3. NOTE: OBSERVERA! PRECAUTIONS Power supply/AC power adaptor Location Do not open PLEASE READ CAREFULLY BEFORE PROCEEDING CAUTION Page Introduction Included Accessories Contents The Control Panel Setting Up Selecting & Playing Voices Playing the Demonstration Tunes The Dual Mode Reverb The Control Panel The Control Panel Setting Up Power supply connections Using the OUTPUT R and L/L+R Jacks Using An AC Power Adaptor Z Setting Up Music Stand Using the MIDI IN and OUT Connectors Using the PHONES Jacks Using the Damper Pedal (connect a footswitch to the DAMPER Jack) Selecting & Playing Voices Turn Power On Playing the Demonstration Tunes Engage the Demo Mode Play a Voice Demo Voice Demo Exit From the Demo Mode Engage the Preset Song Mode Play a Preset Song Preset Song Exit From the Preset Song Mode Preset Song A-B Repeat Specify the Beginning (A) of the Phrase Specify the End (B) of the Phrase Stop Playback Preset Song Part Cancel Turn the Desired Part Off Start/Stop Playback Synchro Start Soft Pedal Start/Stop The Dual Mode Other Dual Mode Functions Reverb Adjusting Reverb Depth The Effect Adjusting Effect Depth Touch Sensitivity HARD MEDIUM SOFT FIXED Transposition The Metronome & Tempo Control The Metronome Metronome Time Signature Metronome Volume Function Tempo Control Using the User Song Recorder Recording Make All Necessary Initial Settings Engage the Record Ready Mode Select the Record Track Using the User Song Recorder Start Recording Stop Recording Erasing a Single Track Changing the Initial Settings Playback Using the User Song Recorder Synchro Start Soft Pedal Start/Stop The Function Mode To Select a Function Z X C F1 F2 F2.1: Scale F2.2: Base Note F3 F3.1: Dual Balance F3.2: Dual Detune F3.3: 1st Voice Octave Shift F3.4: 2nd Voice Octave Shift F3.5: 1st Voice Effect Depsth F3.6: 2nd Voice Effect Depth F4 F5 F6 F7 F7.1: MIDI Transmit Channel Selection F7.2: MIDI Receive Channel Selection F7.3: Local Control ON/OFF F7.4: Program Change ON/OFF F7.5: Control Change ON/OFF F7.6: MIDI Transmit Transpose F7.7: Panel/Status Transmit F7.8: Bulk Data Dump F8 F8.2: MIDI F8.3: Tuning F8.4: Pedal F8.1: Voice Using the MIDI Functions What Is MIDI? Using the MIDI Functions Connecting to a Personal Computer Using the MIDI Functions Factory Preset Recall Options Troubleshooting Voice Descriptions Voice Demo Tune Titles Demo and Preset Song List Preset Song Titles Function Factory Setting List MIDI Data Format 3 MODE MESSAGES Data format: [BnH] -> [cc] -> [vv] Data format: [8nH] -> [kk] -> [vv] 2. CONTROL CHANGE Data format: [BnH] -> [cc] -> [vv] 4. PROGRAM CHANGE Data format: [CnH] -> [ppH] 5. SYSTEM REALTIME MESSAGES 6. SYSTEM EXCLUSIVE MESSAGES (Yamaha MIDI Format) Data format: [F0H] -> [43H] -> [0nH] -> [7CH] -> ... -> 7. SYSTEM EXCLUSIVE MESSAGES (Universal System Exclusive) Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] -> 8. SYSTEM EXCLUSIVE MESSAGES (XG Standard) (1) XG Native Parameter Change Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] -> [mmH] -> [llH] -> [ddH] -> [F7H] (2) XG Native Bulk Data (reception only) Effect MIDI Map REVERB EFFECT <Table 1> MIDI Parameter Change table ( SYSTEM ) MIDI Implementation Chart Keyboard Stand Assembly Z Assembly Parts X C V B Post-assembly checklist Specifications Limited Warranty 90 DAYS LABOR 1 YEAR PARTS YPP SERIES OF PORTABLE PIANO CONSUMERS RESPONSIBILITIES EXCLUSIONS NORTH AMERICA CENTRAL & SOUTH AMERICA OCEANIA EUROPE AFRICA MIDDLE EAST ASIA