REF | PART |
|
|
NO. | NO. |
|
|
N° DE | N° DE |
|
|
RÉF | PIÈCE | DESCRIPTION | DESCRIPTION |
1 | Flat Washer .344 ID x .875 OD | Rondelle plate 0,344 DI x 0,875 DE | |
2 | Hex. Scr. | Vis à tête hex. | |
3 | Lockwasher 3/8" ID | Rondelle frein 3/8" DI | |
5 | Handle Knob Assembly | Bouton | |
7 | Hex Hd Cap Scr. | Vis à tête hex. | |
8 | Chute Bracket | Support d’évacuation | |
9 | Shell Alvania Grease (3 oz.) | Graisseur ( 3oz.) | |
10 | Extended Lower Black Plastic Chute | Partie inf. noir de la bouche d’évacuation plastique | |
11 | Ultra Grey Loctite #5699 | Loctite n°. 5699 | |
12 | Upper Black Plastic Chute | Partie sup. noir de la bouche d’évacuation | |
13 | Carriage Bolt | Boulon ordinaire | |
14 | Plastic Bushing .380 ID | Coussinet plastique 0,380 DI | |
15 | Chute Brkt. | Support de la bouche d’évacuation | |
16 | Chute Adapter | Adaptateur | |
17 | Cupped Washer .345 ID x .88 OD x .06 | Rondelle creuse 0,345 DI x 0,88 DE x 0,06 | |
18 | Hex Screw | Vis à tête hex. | |
19 | Hex Flange | Contre écrou hex | |
20 | Chute Flange Keeper | ||
21 | Lockwasher 5/16" ID | Rondelle frein 5/16 DI | |
22 | Flange | ||
23 | Hex Wash HD Tap Scr | Vis à tête hex et rondelle | |
24 | Bow Tie Cotter Pin | Goupille fendue | |
26 | Spacer 1.5 x 1.0 ID x 1.0" Lg. | Entretoise 1,5 x 1,0 DI x 1,0 po de lg. | |
27 | Spacer 1.5 x 1.0 ID x 2.5" Lg. | Entretoise 1,5 x 1,0 DI x 2,5 po de lg. | |
28 | Flange Bushing 1.05 ID x 1.16 OD | Coussinet 1,05 DI x 1,16 DE | |
29 | #9 | Clavette | |
30 | Roulement autoaligner 0,875 DI | ||
31 | Hex Flg. | ||
32 | Flat Washer 1.010 x 1.88 x .060 | Rondelle plate 1,010 x 1,88 x 0,06 | |
33 | 05244A | Bearing Housing | Boîtier de roulement |
34 | Belt Keeper Studs | Goujons du protecteur de la courroie | |
38 | Carriage Bolt | Boulon ordinaire | |
43 | Drift Cutter | Virole de réglage | |
45 | * | Snowthrower Housing Ass’y | Logement du |
46 | * | Shave Plate | Grattoir |
48 | Arctic Grease | Graisse Arctic | |
52 | Carriage Bolt | Boulon ordinaire | |
53 | Carriage Bolt | Boulon ordinaire | |
54 | Gear Housing Support Plate 1 x 3/16 | Support du carter d’engrenages 1 x 3/16 x | |
56 | Hex Flange | Contre écrou hex | |
58 | Spring Spirol Pin Heavy - 5/16 dia x 1.7 | Goupille en spirale 5/16 dia x 1,75 po de lg | |
59 | Blower Fan Ass’y Complete | Ventilateur du | |
60 | Gear Housing Support Bracket | Support du carter d’engrenage | |
61 | Barbed Plug | Bouchon | |
63 | * | Spiral Axle | Essieu en spirale |
65 | Gear Housing Half - RH | Carter d’engrenage au moitié - droit | |
67 | #9 | Clavette | |
68 | Auger Drive Shaft | Arbre d’entraînement | |
69 | Snap Ring for .875 dia. shaft | Jonc d’arrêt pour arbre de 0,875 dia. | |
70 | Oil seal for .875 ID Garlock (76 x 6133) | Joint d’étanchéité d’huile (76 x 6133) | |
71 | Sleeve Bearing .875 ID | Palier à douille 0,875 DI | |
72 | Thrust Bearing .88 ID x 1.44 OD x .078 | Palier à butée 0,88 DI x 1,44 DE x 0,078 | |
73 | Flat Washer .88 ID x 1.4 OD x .125 | Rondelle plate 0,88 DI x 1,4 DE x 0,125 | |
74 | Worm Gear LH Double Thread | Vis sans fin à double filetage gauche | |
76 | Flat Washer 1.5 ID x 2.0 OD x .03 | Rondelle plate 1,5 DI x 2,0 DE x 0,03 | |
77 | Worm Gear LH Double Thread (Bronze) | Vis sans fin à double filetage - gauche bronze | |
78 | Worm Gear Shaft | Support du carter d’engrenage | |
79 | #91 Woodruff Key 1/4 x 3/4 Dia. | Clavette Woodruff no 91 1/4 x 3/4 | |
|
|
|
|
Continued on next page/Suite à la page prochaîne
* See chart on next page./ Voir le tableau à la page prochaîne
23