Yorkville Sound YS1083 owner manual Master Section

Master Section

1. MAIN Control

The MAIN control adjusts the overall level of the main mix, the PA volume.

Note: To ensure maximum sig- nal headroom and clarity, first set the MAIN level control to 7, then set the channel LEVEL controls for a good signal with- out clipping, then go back to the MAIN level control and adjust for the overall volume desired.

E f f e c t s

1.	Hall			9.	Slap Back
2.	Chamber		10.		Echo
3.	Lg Room		11.		Flanger
4.	Sm Room		12.		Chorus
5.	Stage		13.		Chorus Room 1
6.	Ambience		14.		Chorus Room 2
7.	Arena		15.		Dry Vocal
8.	Stadium		16.		Rotary Speaker
			15	16	1	2	3
	EFX	14					4
	clip	13					5
		12					6
			11 10		9	8	7

Tape/CD In Record OUT

			E Q U A L I Z E R													VU Meter
100		250	500		1.0K		2.0K			5.0K	10.0K						Clip
												+15
												+10					+3
												+5
													0				0 dB
													-5				-6
													-10
													-15				-12
													2 x 90 Watt Mixer
	Power												with 24-Volt
													Phantom Power
4	5	6	4		5	6		4		5	6	3		4		5	6
3		7	3				7	3			7						7
2		8	2				8	2			8	2					8
1		9	1				9	1			9	1					9
0		10	0			10		0		10				0			10
Record Out				EFX Level					Tape/CD In						MAIN
Level

1/4-inch Phone Plug

1/4-inch T.R.S. Phone Plug

XLR Plug

2. MAIN EFFECTS Level Control

The MAIN EFX control adjusts the amount of signal from the output of the internal Digital Effects Processor to the MAIN mixing bus where it is mixed with the audio signal from the CHANNEL LEVEL controls. The MAIN EFX control adjusts the intensity of the effects on the left and right MAIN output signals.

3. Record OUT Jacks

The Record OUT audio signal at the Record OUT RCA jacks is the MAIN audio signal from channels 1 to 5, but without DIGITAL EFFECTS, and pre-GRAPHIC EQUALIZER. The Record OUT level control, located to the left of the MAIN control, adjusts the audio signal level going to these jacks. Using RCA patch cords, connect directly to the inputs (line-level) of an audio recording device.

4. Power LED and VU-Meter LED Display

The Power LED lets you know that the MM5D is plugged in, turned on and all systems are normal. The VU-Meter LEDs indicate the level of the audio signal going to the internal power amplifiers. The 0dB VU-Meter LED indicates when the amplifiers are delivering full power. Because there is an audio limiter on the input of each power amplifier, you can turn up the MAIN level control until the VU-Meter Clip LED illumi- nates where the audio limiter is at maximum compression. For maximum audio power output the MM5D sounds the best if the +3dB VU-Meter LED is illuminated but the VU-Meter Clip LED does not illuminate.

5. Phantom Power

Regular dynamic microphones can be used with the Phantom Powered XLR Channel inputs. Connecting a dynamic or condenser microphone to the MM5D when the MM5D’s power is on will create a loud, potentially damaging pop in the loudspeakers. When setting up, turn off the MM5D’s AC power, connect all of your microphones then turn the MM5D power on.

6. Tape/CD Input

There are left and right RCA inputs jacks on the front panel to connect a CD player, cassette player, MP3 player, or other stereo source to the mixer. These inputs connect directly to the MAIN bus, and to the Record OUT bus. The Tape/CD level control adjusts the input level of the audio signal.

1/4-inch T.R.S.		XLR Plug
	Phone Plug	(Male)

Tip = 0°					Pin 1	= Ground
		Ring = 180°
					Pin 2	= 0°
			1	2
	Sleeve = Ground			3	Pin 3	= 180°

Balanced 1/4-inch T.R.S. to Balanced XLR 3