Prior to using for the first time
Before using your dishwasher for the first time:
1.Ensure that the electrical and water connections comply with the installation instructions.
2.Remove all packaging from inside the appliance.
3.Set the water softener.
4.Pour 1 litre of water inside the salt container and then fill with salt.
5.Fill the rinse aid dispenser.
6.Run a "Rinse and Hold" programme.
Setting electronically
The dishwasher is factory set at level 3. If it’s necessary to set a new level, proceed as follows.
1 . With the dishwasher switched off press function push |
| |||
buttons | 1 and | 2 simultaneously . |
|
|
2. While keeping the push buttons | 1 and | 2 pressed switch on | ||
the dishwasher by pressing the On/Off push button. |
| |||
The On/Off indicator light comes on. |
|
| ||
At the same time, the indicator lights of push buttons | 1 and | |||
2start flashing.
Setting the water softener
The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.
The higher the content of these salts, the harder your water is. Water hardness is measured in equivalent scales, Clarke degrees, French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.
The water softener must be set in both ways: manually, using the water hardness switch and electronically, using the function push buttons on the control panel.
If your water is level 1 it is already soft and therefore there is no need to use salt.
Setting manually
1.Open the dishwasher door.
2.Remove the lower basket from the dishwasher.
3. Turn the water hardness switch to position 1 or 2 (see table).
4.Replace the lower basket.
|
|
|
|
| SO568 |
3. Press push button |
| 1 , the indicator light of push button | 2 | ||
turns off, while the indicator light of push button | 1 remains | ||||
fixed for about 5 seconds, after this it starts flashing |
| ||||
indicating the current level of the water softener. |
| ||||
SO569
The current level is indicated by the number of flashes
made by the indicator light of push button1 , that alternates 5 seconds off with a number of flashes, this for about 60
seconds.
Example: |
The dishwasher is factory set at position 2.
AA07 |
1 flash |
| = | level 1 | ||
2 | flashes | = |
| level 2 | |
3 | flashes | = |
| level 3 | |
4 | flashes | = |
| level | 4 |
5 | flashes | = |
| level | 5 |
4. To change the level, press push button | 1 . Each time the | |
push button is pressed the level changes. |
|
|
Example: |
|
|
if the current level is 3, by pressing push button | 1 | once, |
level 4 is selected. |
|
|
if the current level is 5, by pressing push button | 1 | once, |
level 1 is selected. |
|
|
The indicator light of push button | 1 remains off for about 5 |
|
seconds after which it starts flashing indicating the new level selected.
5.To memorise the new level, switch off the dishwasher by pressing the On/Off push button.
|
| Water hardness |
|
| Adjusting the water hardness |
|
| |||
|
|
|
|
|
|
|
|
| ||
Clarke |
| French | PPM | Number of | Use of | |||||
|
| setting | ||||||||
degrees |
| degrees | (parts per million) |
| flashes | salt | ||||
|
|
| ||||||||
| manually | electronically | ||||||||
|
|
| (°TH) |
|
|
|
| |||
|
|
|
|
|
|
|
| |||
50 - 63 |
| 71 - 90 | 701 - 900 | 2 | level 5 | 5 | yes | |||
|
|
|
|
|
|
|
|
|
|
|
36 | - 49 |
| 51 | - 70 | 501 | - 700 | 2 | level 4 | 4 | yes |
|
|
|
|
|
|
|
|
|
|
|
22 | - 35 |
| 31 | - 50 | 301 | - 500 | 2 | level 3 | 3 | yes |
6 | - 21 |
| 8 - | 30 | 80 - | 300 | 1 | level 2 | 2 | yes |
|
|
|
|
|
|
|
|
| ||
| < 6 |
| < 8 | < 80 | 1 | level 1 | 1 | no | ||
|
|
|
|
|
|
|
|
|
|
|
5
