If only a cold water supply is available, connect the two hoses to a cold water outlet by means of a «Y» connection piece.

Installation should comply with local water authority and building regulations’ requirements.

The appliance must be given a separate cold water supply and not be connected to a mixer tap, a single outlet water heater or a booster pump. A minimum water pressure of 0.48 bar is required for safe operation of the appliance.

If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system.

There should be a minimum distance of 5.02m

(161/2 ft) between the appliance’s inlet and the bottom of the water storage tank.

There will be sufficient pressure for the hot water supply, providing there is a minimun height of 2.74 metres (9 ft) between the bottom of the cold water storage tank and the bottom of the hot water cylinder.

Set the hoses correctly by loosening the ring nuts. After positioning the inlet hoses, be sure to tighten the ring nuts again to prevent leaks.

P0021

Water drainage

This appliance is designed to be permanently plumbed into your home's water supply and drainage system.

The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece” supplied.

3 pin

 

 

90 cm.(35.4")

cm.

 

Max.

Min.60

(23.6")

P1039

 

 

The standpipe should have an internal diameter of approximately 38mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe.

When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90cm (35.4'') and no less than 60cm (23.6'') above floor level. The upright standpipe should have a minimum length of 30cm (12'') from the bottom of the elbow to the top of the pipe (see diagram).

Make sure that it is designed in such a way, that the end of the drain hose cannot be covered with water.

cm.(12")

 

standpipe

 

 

1

 

 

 

38 mm.(1/2") diameter

Min. 30

 

 

 

 

 

 

P1040

The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter of 18mm.

If you intend the drain hose to empty into a sink, make sure that the sink is empty and the plug hole is not blocked. Use the plastic “U-Piece” supplied.

P0022

Important

Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.

22

Page 21 Page 23
Page 22
Image 22
Zanussi ZJ 1284 manual Water drainage
Page 21 Page 23

ZJ 1284 specifications

The Zanussi ZJ 1284 is a versatile and efficient kitchen appliance that stands out in the realm of modern cooking. Known for its sleek design and innovative features, this kitchen wonder offers a variety of functionalities that cater to the needs of both amateur cooks and seasoned chefs.

At the heart of the Zanussi ZJ 1284 is its powerful performance, boasting a robust motor that ensures consistent results in every operation. This makes it perfect for a wide range of cooking tasks, from blending and pureeing to mixing dough. The appliance's capacity is designed to accommodate various cooking volumes, allowing users to prepare meals for both small families and larger gatherings with ease.

One of the standout features of the Zanussi ZJ 1284 is its multi-speed settings. This allows users to select the ideal speed for each task, ensuring precision whether you are whipping cream or chopping vegetables. The comprehensive speed options are complemented by a pulse function, which provides an extra boost of power for tough mixing tasks.

Moreover, the Zanussi ZJ 1284 is equipped with a number of safety features, ensuring peace of mind during use. The device has an automatic shut-off function that activates when the lid is not properly secured, preventing any unexpected accidents. The durable materials used in its construction also contribute to its longevity, making it a reliable addition to any kitchen.

In terms of design, the Zanussi ZJ 1284 showcases a contemporary aesthetic that fits seamlessly into modern kitchen environments. Its compact size allows for easy storage, while the intuitive controls make it simple to operate. The appliance is also easy to clean, with removable parts that are dishwasher safe.

Another notable characteristic of the Zanussi ZJ 1284 is its energy efficiency. Designed to minimize power consumption, this appliance is perfect for those looking to reduce their environmental footprint while still enjoying high-performance cooking capabilities.

In conclusion, the Zanussi ZJ 1284 combines style, functionality, and safety features, making it an ideal choice for anyone looking to enhance their culinary skills. With its powerful motor, versatile settings, and sleek design, this appliance promises to transform cooking into a delightful experience. Whether you are an aspiring cook or a kitchen expert, the Zanussi ZJ 1284 is sure to become an indispensable tool in your culinary arsenal.
Top Page Image Contents