Fixing to the adjacent units
Levelling
II29 |
Insert the two fixing brackets into the slots provided in the top front part of the dishwasher, as shown in the figure.
Secure the brackets to adjacent units using two 3,5 x 16 screws for each bracket.
Make sure that the dishwasher door closes properly, without rubbing on sides. Otherwise level the machine by slightly screwing or unscrewing the two front feet until perfect closure of the door is reached.
Kitchen plinth adjustment
To allow correct opening of the door it is sometimes necessary to cut the kitchen plinth. Refer to the
Important!
The dishwasher must be secured against tilting. Therefore, make sure that the counter it is fitted under, is suitably secured to a fixed structure (adjacent kitchen cabinets, wall).
Attention!
cutting table below.
When the dishwasher is secured to the kitchen cabinets, do not drill any holes into the sides of the machine.
Adjusting the door balance
The door of the dishwasher is balanced when it is open in any position.
a
According to dimensions of (a) and (b) as shown on the figure, you will find on the following table the depth (x) of the cut to be made on the plinth.
Fitting the decor panel may sometimes affect this balance. In this case it will
II15
b
be necessary to adjust the balance as follows:
The dimensions (a) and (b) of the table are those more frequently used in the kitchen furnitures.
Height (a)*
1 7 0 1 6 0 1 5 0 1 4 0 1 3 0 1 2 0 11 0 1 0 0
By screwing or unscrewing these screws, the tension of the door balancing springs is increased or decreased respectively.
Attention!
The weight of the panel should be within the limits given in the "dimensions of the panel", otherwise balancing the door will not be possible.
PII04GB
| 40 | 136 | 131 | 125 | 118 | 110 | 100 | 93 | 85 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 50 | 135 | 131 | 125 | 118 | 110 | 102 | 92 | 85 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(b)* | 60 | 137 | 132 | 125 | 118 | 110 | 102 | 94 | 85 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
70 | 138 | 134 | 128 | 120 | 110 | 104 | 95 | 85 |
| X | |||||
Depth |
| ||||||||||||||
80 | / | 139 | 130 | 124 | 115 | 105 | 98 | 88 |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 90 | / | / | 138 | 129 | 120 | 110 | 100 | 90 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 0 0 | / | / | / | 135 | 125 | 115 | 105 | 95 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*dimensions in mm |
|
| 600 mm |
|
|
|
|
| |||||||
|
|
|
|
| (minimum) |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
X Dimensions of the cut on the plinth 
19
