Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies 170PAX2TM manual Feed Key Self Test

Models: 170PAX2TM

1 84

Download 84 pages 58.81 Kb

Page 48

Troubleshooting

FEED Key Self Test

Press and hold the FEED key while turning the printer power ON. Release the key anytime after the first front panel LED turns OFF.

NOTE: The CANCEL Key Self Test should be performed prior to this self test. Information on the printed configuration label can be used with the results of this self test to determine the best darkness setting for a specific media/ribbon combination.

The labels printed during this print quality test depends on the dot density of the printhead.

•300 dpi printers: 7 labels are printed at the 2 ips and 8 ips print speeds.

•200 dpi printers: 7 labels are printed at the 2 ips and 12 ips print speeds.

Each label is printed at a different darkness setting, starting at three settings below the currently configured value and continuing to increase until it is three settings darker than the configured value. The relative darkness and speed are printed on each label. The bar codes on these labels can be ANSI-graded to check print quality.

Compare these labels to determine which has the best print quality. Then add or subtract the value printed on that label from the darkness value specified on the configuration label. The resulting numeric value (0 to 30) is the best darkness value for that specific media/ribbon combination. Use the front panel configuration process to set the Print Darkness parameter to the new value. Refer to Figure 18 for an example of the label.

	Figure 18. FEED Key Self Test
44	170PAX2-Series User’s Guide

Image 48

Zebra Technologies 170PAX2TM manual Feed Key Self Test

Contents

Zebra 170PAX2 -Series User ’s Guide Proprietary Statement Product ImprovementsFCC Compliance Statement Canadian DOC Compliance StatementContents Options 170PAX2-Series User’s GuideIntroduction Zebra 170PAX2 Print EngineGetting Started Print Engine MountingPrinter Power Cable ConnectionsMedia & Ribbon Loading Media LoadingMedia Loading Left-Hand Units Ribbon Loading Right Hand UnitsRemoving Used Ribbon Left Hand UnitsMedia Sensor Position Reflective Media SensorTransmissive Media Sensor 170PAX2-Series User’s Guide Power On/Off Switch Printer OperationFront Panel Keys Front Panel Indicator Lights LEDs Liquid Crystal DisplayControl Panel Keys Configuration and Calibration Entering the Program ModeChanging Password-Protected Parameters Leaving the Program ModeConfiguration Process Setting Print ParametersSetting Darkness Setting the Tear Off Position Selecting the Print ModeSelecting the Media Type Selecting the Sensor TypeSetting the Print Width Setting the Maximum Label LengthSelecting the Print Method Label Feed Listing Printer Information Initialize Card 170PAX2-Series User’s GuideMedia and Ribbon Sensor Calibration Sensor ProfileMedia and Ribbon Calibration Setting Communication Parameters Setting the Host PortSetting the Baud Rate Setting the Data BitsSetting the Parity Setting the Stop BitsSetting the Host Handshake Setting the ProtocolSetting the Network ID Setting the Communications ModeSelecting Prefix and Delimiter Characters Control Prefix CharacterFormat Prefix Character Delimiter CharacterSelecting ZPL Mode Setting Ribbon TensionPower Up and Head Close Parameters Media Power UpLabel Positioning Parameters Head CloseBackfeed Sequence Setting the Label Top Position Label Top PositionSetting the Left Position Left Position 170 PAX2-Series User’s GuideHead Test Function Head ResistanceVerifier Port Setting the Applicator Port Applicator PortSetting the Start Print Signal Setting the Resync ModePrinting Controls Selecting the Ribbon Low Feature Reprint ModeSensor Values LCD Adjust Printer LanguageSelecting the Liquid Crystal Display LCD Language Care & Adjustments CleaningCleaning the Exterior Cleaning the InteriorCleaning the Printhead and Platen Roller Sensor Locations Right-Hand Unit ShownPrinthead Pressure Adjustment Toggle PositioningPrinthead Pressure Right-Hand Unit Shown Troubleshooting Power On Self TestPower On Troubleshooting Printer TroubleshootingFor Thermal Transfer For Direct ThermalExplanation of Errors Creating Bitmap Storing BitmapBuilding Format Storing FormatFirst calibrate the printer, then CC , CT , and CD Cancel Key Self Test Printer Self TestsIntroduction Pause Key Self Test Pause Key Test Sample Printout 170PAX2-Series User’s GuideFeed Key Self Test Feed Key Self TestFeed Key and Pause Key Parameter Controlled byCommunications Diagnostics Test Results of Communications Diagnostic TestOptions Single In-line Memory Module SimmCommunication Interfaces ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Printer Specifications Media SpecificationsRibbon Specifications Printing ConsiderationsCommunications Specifications Zebra Programming Language ZPLBar Codes Standard Printer Fonts Memory PhysicalElectrical FusesAC Power Cord Requirements Power Fuse ReplacementAC Power Cord Specifications Appendix aInstalling a Fuse ShippingAppendix B Printer Communications Interface Technical InformationSystem Considerations Interface ConsiderationsRS-232/RS-422/RS-485 Serial Data Port RS-232/RS-422/RS-485 PinoutsPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port Applicator Interface Connector DB-15 Connector Printer to ApplicatorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Ascii Code Chart Appendix C170PAX2-Series User’s Guide Adjusting Darkness For In-Spec Bar Codes Appendix DIn-Spec Bar Code Darkness ComparisonInstallation Information Appendix EFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide Glossary 170PAX2-Series User’s GuideGlossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation