Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies 170PAX2TM manual Initialize Card, 170PAX2-Series User’s Guide

Models: 170PAX2TM

1 84

Download 84 pages 58.81 Kb

Page 21

Configuration and Calibration

Initialize Card

This selection initializes the optional memory card.

CAUTION: Perform this operation only when it is necessary to erase all previously stored information in the optional memory card. Otherwise, press the NEXT key to bypass this function and display SENSOR PROFILE.

INITIALIZE CARD

YES

1.Press the right oval key to select “YES”. If your printer is set to require a password, you will now be prompted to enter the password. Enter the password then press the NEXT key.

INITIALIZE CARD

YES

2.The display will ask “INITIALIZE CARD?” Press the right oval key to select “YES”. The front panel LCD will ask “ARE YOU SURE?”

ARE YOU SURE?

NOYES

3.Press the right oval key to select “YES” and begin the initialization. or

Press the left oval key “NO” to cancel the request and return to the “INITIALIZE CARD” prompt.

4.Press the SETUP/EXIT key followed by the NEXT key.

If initialization is still in process, the front panel display will flash back and forth between the two phrases “CHECKING B: MEMORY” and “PRINTER IDLE.”

When initialization is complete, the printer will automatically exit the configuration mode and the front panel will display “PRINTER READY”.

NOTE: Depending on the amount of memory in the memory card, initialization may take up to five minutes to complete.

170PAX2-Series User’s Guide

17

Image 21

Zebra Technologies 170PAX2TM manual Initialize Card, 170PAX2-Series User’s Guide

Contents

Zebra 170PAX2 -Series User ’s Guide Product Improvements Proprietary StatementFCC Compliance Statement Canadian DOC Compliance StatementContents 170PAX2-Series User’s Guide OptionsZebra 170PAX2 Print Engine IntroductionGetting Started Print Engine MountingCable Connections Printer PowerMedia Loading Media & Ribbon LoadingMedia Loading Left-Hand Units Right Hand Units Ribbon LoadingLeft Hand Units Removing Used RibbonMedia Sensor Position Reflective Media SensorTransmissive Media Sensor 170PAX2-Series User’s Guide Power On/Off Switch Printer OperationFront Panel Keys Front Panel Indicator Lights LEDs Liquid Crystal DisplayControl Panel Keys Entering the Program Mode Configuration and CalibrationChanging Password-Protected Parameters Leaving the Program ModeConfiguration Process Setting Print ParametersSetting Darkness Selecting the Print Mode Setting the Tear Off PositionSelecting the Media Type Selecting the Sensor TypeSetting the Print Width Setting the Maximum Label LengthSelecting the Print Method Label Feed Listing Printer Information 170PAX2-Series User’s Guide Initialize CardSensor Profile Media and Ribbon Sensor CalibrationMedia and Ribbon Calibration Setting the Host Port Setting Communication ParametersSetting the Baud Rate Setting the Data BitsSetting the Stop Bits Setting the ParitySetting the Host Handshake Setting the ProtocolSetting the Communications Mode Setting the Network IDControl Prefix Character Selecting Prefix and Delimiter CharactersFormat Prefix Character Delimiter CharacterSetting Ribbon Tension Selecting ZPL ModePower Up and Head Close Parameters Media Power UpLabel Positioning Parameters Head CloseBackfeed Sequence Label Top Position Setting the Label Top PositionLeft Position 170 PAX2-Series User’s Guide Setting the Left PositionHead Test Function Head ResistanceVerifier Port Applicator Port Setting the Applicator PortSetting the Start Print Signal Setting the Resync ModePrinting Controls Selecting the Ribbon Low Feature Reprint ModeSensor Values LCD Adjust Printer LanguageSelecting the Liquid Crystal Display LCD Language Cleaning Care & AdjustmentsCleaning the Exterior Cleaning the InteriorSensor Locations Right-Hand Unit Shown Cleaning the Printhead and Platen RollerToggle Positioning Printhead Pressure AdjustmentPrinthead Pressure Right-Hand Unit Shown Power On Self Test TroubleshootingPrinter Troubleshooting Power On TroubleshootingFor Thermal Transfer For Direct ThermalStoring Bitmap Explanation of Errors Creating BitmapBuilding Format Storing FormatFirst calibrate the printer, then CC , CT , and CD Cancel Key Self Test Printer Self TestsIntroduction Pause Key Test Sample Printout 170PAX2-Series User’s Guide Pause Key Self TestFeed Key Self Test Feed Key Self TestParameter Controlled by Feed Key and Pause KeyResults of Communications Diagnostic Test Communications Diagnostics TestSingle In-line Memory Module Simm OptionsCommunication Interfaces ZebraNet Micro Print Server MPS170PAX2-Series User’s Guide Media Specifications Printer SpecificationsRibbon Specifications Printing ConsiderationsCommunications Specifications Zebra Programming Language ZPLBar Codes Standard Printer Fonts Physical MemoryElectrical FusesPower Fuse Replacement AC Power Cord RequirementsAC Power Cord Specifications Appendix aShipping Installing a FusePrinter Communications Interface Technical Information Appendix BSystem Considerations Interface ConsiderationsRS-232/RS-422/RS-485 Pinouts RS-232/RS-422/RS-485 Serial Data PortPin to 25-Pin Interconnecting Cable RS-422/RS-485 Interconnecting Cable Centronics-Compatible Parallel Data Port Applicator Interface Connector DB-15 Connector Printer to ApplicatorCabling Requirements See the Configuration and Calibration section Fuse 1 JP1 JP2 Appendix C Ascii Code Chart170PAX2-Series User’s Guide Appendix D Adjusting Darkness For In-Spec Bar CodesBar Code Darkness Comparison In-SpecAppendix E Installation InformationFront View of Right Hand Printer 451 748 11.45 mm 222.2 mm 170PAX2-Series User’s Guide 170PAX2-Series User’s Guide GlossaryGlossary Printer configuration See configuration 170PAX2-Series User’s Guide Index Index Index Page Page Zebra Technologies Corporation