Zenith XBV323 warranty Tape Operation Normal Playback, Special Effect Playbacks

Tape Operation

Normal Playback

Preparation:

Turn on the TV.

Tune the TV to the DVD+VCR output channel (CH 3 or 4) or set the TV’s source selector to VIDEO.

If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO. Set the Output Source to VCR as shown in “Selecting the Output Source” on page 6.

1	Insert a prerecorded video cassette.
	The	indicator will light and the DVD+VCR will

power-up automatically.

Make sure that the indicator in the display window is not lighted. If it is, press POWER once. If a tape without a safety tab is inserted, the unit will start playback automatically.

2 Press PLAY (H) once.

PLAY appears on the TV screen .

It is not necessary to select the tape speed for playback. It will be automatically selected by the DVD+VCR.

In playback, the TV/VCR selector switches to VCR mode automatically.

3 Press STOP (x) to stop playback. STOP appears on the TV screen.

If the tape reaches the end before STOP (x) is pressed, the DVD+VCR will automatically stop, rewind and eject the tape, and it will turn itself off.

Tracking Control

Auto Tracking

The automatic tracking function adjusts the picture to remove snow or streaks.

The AUTO TRACKING function works in the following cases:

A tape is played back for the first time. Tape speed (SP, LP, SLP) changes.

Streaks or snow appear because of scratches on the tape.

Manual Tracking

If noise appears on the screen during playback, press either v/V on the remote control or CH (v/V) on the front panel until the noise on the screen is reduced.

In case of vertical jitter, adjust these controls very carefully. Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more than 3 seconds.

Special Effect Playbacks

Special effects playback notes

Horizontal lines (noise bars) will appear on the TV screen. This is normal.

The audio is automatically muted during special effect modes, so there is no sound during search.

During high-speed picture search mode, a short period is needed to stabilize tape speed when re-entering the PLAY mode. Slight interference may be observed during this period.

Search

This function lets you quickly and visually search for a desired tape section in either direction: forward or reverse.

1	Press BACKWARD (.) or FORWARD (>)	OPERATION
	during playback.
	The DVD+VCR will be activated in the SEARCH
	mode.
	If the DVD+VCR is left in the SEARCH mode for more
	than 3 minutes, the DVD+VCR will automatically enter the
2	PLAY mode, to protect the tape and video heads.
	To return to playback, press PLAY (H).

Still Picture and Frame-by-Frame Playback

1Press PAUSE/STEP (X) during playback. Still picture will appear on the TV screen.

If a still picture vibrates vertically, stabilize it using v/V on the remote control.

If the DVD+VCR is left in the STILL mode for more than 5 minutes, the DVD+VCR will automatically enter the STOP mode to protect the tape and video heads.

2Press PAUSE/STEP (X) repeatedly to advance the video picture one frame at a time while viewing a still picture.

3To return to playback, press PLAY (H).

Slow Motion

1While in still mode, press FORWARD (>).

The tape will be played back at a speed 1/19 times slower than the normal speed.

During slow playback, use v/V on the Remote Control to minimize noise bands.

If slow motion mode continues for more than 3 minutes, the DVD+VCR will automatically change to playback mode.

2To return to playback, press PLAY (H).

CM Skip (Commercial Skip)

This is useful for skipping commercials or short program segments.

1Press CM Skip during playback.

The tape will fast forward picture search through 30 seconds of recording.

Skipping time can be extended by pressing CM Skip repeatedly.

Subsequent presses result in advancing the fast forward picture search time by 30-second increments (maximum 3 minutes).

2When the search is complete, the DVD+VCR will go into playback mode automatically.

EZ (EASY) Review

You can replay a specified segment twice.

1	During playback, press and hold EZ REVIEW for
	more than 3 seconds at the end of the segment
	and your VCR will start reverse search.

2 Release EZ REVIEW at the beginning of the segment. The segment is replayed twice automatically.

To return to normal play, press PLAY (H) during easy review playback.

21